What is the power developed by the armature?(a) 49.28 kW(b) 47.08 kW(iv)(c) 44.76 kW(d) 42.58 kW(e) 41.03 kW(v)What is the value of rotational losses for the motor?(a) 1549 W(b) 1793 W(c) 1990 W(d) 4500 W(e) 8248 W(vi)What is the efficiency of the motor?(a) 81.09%(b) 85.60%(c) 87.15%(d) 91.26%(e) 96.36%(vii)What is the motor no-load speed if the no load induced voltage is 440.85V?(а) 390 грm(b) 395 грm(c) 400 rpm(d) 405 rpm(е) 410 грm(viii) What would be the starting line current if the motor was started at full-voltage?(a) 4107 A(b) 4255 А(c) 4392 A(d) 4400 A(e) 4408 A(ix)What is the motor full-voltage starting line current if a 1.90 starting resistor is connectedin series with the armature?(a) 212 A(b) 220 A(c) 228 A(d) 231.6 A(e) 239.6 A1217 words& Accessibility: Investigate Question 4A 55 hp, 440 V, 400 rpm DC shunt motor draws 107 A when operating at rated conditions. Themotor has an armature-circuit resistance of 100 m2 and a total field-circuit resistance of 55 2.Draw a schematic of the motor in the space below showing all known quantities (resistances,currents, voltages and load). Show only symbols for unknowns.Determine the following for rated operationWhat is the motor armature current?(a) 99 A(b) 102 A(c) 107 A(d) 110 A(e) 115 A(i)What is the CEMF developed in the armature?(a) 449.9 V(b) 440.0 V(c) 430.1 V(d) 429.3 V(e) 428.5 V(i)What is the total windings (copper) losses in the motor?(a) 4842.5 W(b) 4500.1 W(c) 3520 0 W(d) 1145 W(e) 980.1 W

Answered: Image /qna-images/answer/53813aac-495d-4e68-937e-b476ca93f03b.jpg

() What is the motor armature current? (a) 99 A (b) 102 A (c) 107 A (d) 110 A (e) 115 A (ii) What is the CEMF developed in the armature? (a) 449.9 V (b) 440.0 V (c) 430.1 V (d) 429.3 V (e) 428.5 V (iii) What is the total windings (copper) losses in the motor? (a) 4842.5 W (b) 4500 1 W (c) 3520 0 W (d) 1145 W (e) 980.1 W 目

() What is the motor armature current? (a) 99 A (b) 102 A (c) 107 A (d) 110 A (e) 115 A (ii) What is the CEMF developed in the armature? (a) 449.9 V (b) 440.0 V (c) 430.1 V (d) 429.3 V (e) 428.5 V (iii) What is the total windings (copper) losses in the motor? (a) 4842.5 W (b) 4500 1 W (c) 3520 0 W (d) 1145 W (e) 980.1 W 目

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Draw the circuit diagram of self excited DC shunt generator, mark all current and voltages and write the necessary equations. write any two applications for the same.
Q1/A) Fill in the following blanks 1. The air gap between stator and rotor is about...mm 2. The iron losses are depending on ..4sker,.ddcam 3. The relationship between stator and rotor current frequency is ....... 4. The range of operation mode slip is ...... 5. The relationship between hysteresis loss and frequency is .... 22 1-V T
.
15. What are the following statements are true for DC Motor? I. Motor converts Electrical Energy to Mechanical Energy II. Motor supply current to the armature winding III. Back EMF is lesser than the Supply voltage IV. Fleming's Right-hand rule a. I and II b. II and IV c. I,II and III d. I,II and IV
4-pole, d.c. shunt motor has a flux per pole of 0.04 Wb and the armature is lap-wound with 720 conductors. The shunt field resistance is 240 Ω and the armature resistance is 0.2 Ω. Brush contact drop is 1V per brush. Determine the speed of the machine when running (a) as a motor taking 60 A and (b) as a generator supplying 120 A. The terminal voltage in each case is 480 V. 5 3 K4 8 Derive the Torque equation of a D.C Motor.
Q2. Answer two branch only A) Draw the Full-wave rectifier ammeter circuit with Step up transformer? B)Draw the PMMC scheme showing the deflecting and controlling forces? C)Draw the current flowing left to right producing positive deflecting torque?
6. In relation to a compound d.c machine, choose the right statement from the following (A) Both series and shunt field coils have comparable and number of turns and cross sectional areas. (B) Shunt field coil has fewer number of turns and large cross sectional area compared to series field coil. (C) Series field coil has fewer number of turns and large cross sectional area compared to shunt field coil. (D) None of (A), (B) and (C) are correct statement.