I need the answer as soon as possible 6- appraisal question:-1- For the induced electromotive force generated through commutator of 2-polearmature, is it AC or DC.Works as rectifier2- Explain the necessity and principle of commutator in DC generator.3- In the generator, what relation does the revolving velocity of armature has toinduce electromotive force? >4- If the revolving velocity of armature is fixed for a constant direction, how will thepolarity of induced electromotive force are changed when the position of N and Sof permanent magnet used for afield?In other words, explain the change of induced electromotive force when thedirection of the magnetic line of force in magnetic field is changed.

a) In two pole armature when rotor rotate the according to Faraday's law of electromagnetic…

question:- 1- For the induced electromotive force generated through commutator of 2-pole Works as rectifier 2- Explain the necessity and principle of commutator in DC generator. armature, is it AC or DC. E- In the generator, what relation does the revolving velocity of armature has to induce electromotive force? >

question:- 1- For the induced electromotive force generated through commutator of 2-pole Works as rectifier 2- Explain the necessity and principle of commutator in DC generator. armature, is it AC or DC. E- In the generator, what relation does the revolving velocity of armature has to induce electromotive force? >

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

3. Which of the following statements about the use of structural steel as an equipment grounding conductor(EGC) in an AC system is correct?A. Structural steel isn't allowed for use as an EGC.B. Structural steel can be used as an EGC bonding jumper between panelboards.C. Structural steel must have an EGC bonding jumper every three feet of structure.D. Structural steel can be used as an EGC when it's bonded at both ends.
What is the lighting and receptacle demand load for an 1000 sq. m office space with one hundred ten, 15 A, 250 V receptacles. [Office General Lighting Receptacle]
1)The NEC Style Manual indicates that if a term in the NEC appears in more than two articles, it qualifies for a definition in which of the following. a) The articles where the term appears b) Article 90 c) Article 100 d) Table of Contents 2)Definitions of terms related to grounding and bonding and used only in Article 250 are located in ________.a) Article 100 b) Article 200 c) Chapter 9 d) Section 250.2 3)As a general rule, when installing ground rod electrodes, two must be installed always unless a single ground rod provides not more than 25 ohms’ resistance to ground. a) True b) False
Which of the following statements about equipment grounding conductors (EGCS) is true? A. The National Electrical Code permits the EGC to also perform as a grounding electrode conductor. B. More than one EGC must be used if multiple circuits are installed in a single raceway, cable, or cable tray. C. No current should be present in the EGC during normal operation. D. EGCs are required to be decreased in size to address voltage drop.
i need the answer quickly
I need the answer as soon as possible
i need the answer quickly
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
Can I use a distribution box on every floor to distribute telephone lines to their designated outlets?
QUESTION 3 We are running 3 wires and a ground in a RMC to a control panel with a 60 amp circuit breaker disconnect in the control panel. The conduit is run along the ceiling where the ambient air temperature is 100 degrees. The control panel feeds our secondary cooling pump. What size are the ungrounded conductors? All conductors have typeTHHN insulation.
The only way to reach any of the levels where ABC Company is located in a building with ten stories is to use the elevator. In addition, those on the ninth and tenth levels need to connect to a group of servers located on the eighth. Describe the best wiring for the lift shaft. Pick the best option if there is more than one and justify your decision. If you think that interfloor connections may need to operate at substantially greater rates in the future, you may want to reconsider your current option. What is the optimum media for unbounded data transfer requirements? Justify your response.
Why did not I find your solution to all my questions ?