In relation to a compound d.c machine, choose the right statement from the following (A) Both series and shunt field coils have comparable and number of turns and cross sectional areas. (B) Shunt field coil has fewer number of turns and large cross sectional area compared to series field coil. (C) Series field coil has fewer number of turns and large cross sectional area compared to shunt field coil. (D) None of (A), (B) and (C) are correct statement.

In relation to a compound d.c machine, choose the right statement from the following (A) Both series and shunt field coils have comparable and number of turns and cross sectional areas. (B) Shunt field coil has fewer number of turns and large cross sectional area compared to series field coil. (C) Series field coil has fewer number of turns and large cross sectional area compared to shunt field coil. (D) None of (A), (B) and (C) are correct statement.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

1a) As depicted in the figure, input voltage is 120 Volts (RMS) and diode drops are 0.7 Volts. Design this circuit with given two outputs and calculate turns ratio of transformer. i) 10 V ii) 100 V
Untitled Section Jalis 6 In d.c. generators armature reaction is produced by field current O armature current commutating winding current none of the mentioned compensating winding current *.The use of d.c. generators eliminated the use of rectifiers and ac supplies True False O
3. A three phase bridge rectifier is supplied by 380 Volt line voltage through a Star/delta connected transformer of which turns ratio is 1. The firing delay angle is a=30° and the load is resistive R=2.2 Ohm. Draw the circuit diagram and mark the followings on this figure : average values of output voltage, the currents and voltages of each transformer leg.
The primary winding to secondary winding turns ratio of a centre-tapped transformer is 5:1. The primary winding of the transformer is fed from 220V ac supply and the secondary voltage is connected to a single phase full wave rectifier which consist of two diodes. The forward resistance of each diode is 50 and load resistance is 250. Determine the following: A. peak value of current B. de load current C. rms value of load current D. de power E. ac power input to rectifier F. efficiency of rectifier
Please answer this,I want a detailed explanation. An a.c. supply drives a half-controlled thyristor bridge with a resistive load. Sketch the circuit diagram, and the voltage and current waveforms.
If the turns ratio of the transformer shown in the figure above is increased, the forward bias current through the diode is: (a) increases (b) decreases (c) does not change
Which of the following sensors has a permanent magnet inside? Hall effect sensor thru-beam optical sensor piezo-electric sensor LVDT capacitive proximity sensor |o|0|0|6
Q4. A switch-mode power supply is to be designed with the following specifications: Va = 47 V + 10% Vo = 5 V Switching freq. f, = 100 kHz Pioad= 15 – 45 W A forward converter operating in a continuous-conduction mode with a demagnetizing winding (N3=N1) is chosen. Assume all components to be ideal except for the presence of transformer magnetization inductance. a. Calculate N/N1 if this turns ratio is desired to be as small as possible. b. Calculate the minimum value of the filter inductance.
A three-phase bridge rectifier of Figure below has a purely resistive load of R 40 2 and is supplied from a 280-V, 60-Hz source. The b primary and secondary of the input transformer are a Primary + b Secondary ic Van in D₁D3 D5 D4D6D₂ 0₂ connected in Y. Determine the average output voltage of the rectifier if the source inductances are negligible.
Question 2 "The diagram below illustrates a bridge rectifier circuit connected to an ideal transformer with center-tapped windings. Assume that the diodes are ideal. • Plot the instantaneous voltage and current waveforms for the loads R1 (292) and R2 (222), with reference to the center tap of the transformer. • Briefly comment on where this rectifier may be used. Turns ratio=10 240V, 50Hz D1 D4 D3 D2 R=202 R=202
If the turns ratio of the transformer in the figure decreases, the forward current through the diode Please choose one: a. constant b. increase c. reduction
Part A- Why negative peaks are eliminated in Half Wave Rectification and how this can be achieved in Full Wave Rectification without eliminating these peaks? Part B- Is Bridge Full Wave Rectifier only working with Transformers or can we use it with AC source as well? If you are agree with this then provide any advantage of this rectifier circuit without using the transformers OR if you are disagree then provide justification of your answer.