What is the maximum length in km for 1 phase transmission line having conductor of 0.775 square centimeter area over which 220kW at 0.8 power factor and 3500V are to be delivered? The efficiency is 80% and specific resistance is 1.825 micro cm.: O a. 22.85 O b. 18.91 O c. 528.5 O d. 628.5

Q: BJT vs FET

A: Following are the points of difference between BJT and FET: BJT stands for Bipolar Junction…

Q: 8) The resusltant value of two currents that are out of phaso writh each other by 60 oloc đeg is 70…

A:

Q: Ic(sat) + IC Icq 0 .a Vceq Vce(cut-off) VCE RB W +VCC C E RC B=100 RE

A:

Q: 03 Determine operation point of the BJT in figure shown below. Assume B = 200. Rc 330 N RB Vcc 20 V…

A:

Q: Determine Vg, given Vin=25V, V1= - 8V, R;=3k0, R2=5k0 For Ge VK= 0.3 V For Si 0.7 V Ge R1 Si V:. Vo…

A: Find the voltage Vo  All diode forward bias voltage given.

Q: Q6) What are the differences between BJT and JFET?

A: What are the differences between BJT and JFET?

Q: Design a Single-phase bridge rectifier that is required to energize a load with (X) Watts and with…

A: Double-check component datasheets and consider factors like temperature and circuit layout for a…

Q: Q19. Single phase half wave uncontrolled rectifier with pure resistive load of 10 Q is supplied…

A: Given single phase uncontrolled rectifier with pure resistive load Load resistance RL=10 ΩSupply…

Q: A thermocouple has an output e.m.f. as shown in the following table when its hot (measuring)…

A: Given: A thermocouple has an output emf and temperature change are shown in table Temperature (…

Q: A "T" type thermocouple has linear calibration between 0 "C and 400 °C with voltage at maximum…

A:

Q: Q20. Single phase half wave controlled rectifier is supplied from 220 V with 20 2 pure resistive…

A: As per bartleby guideline for more than one subpart asked only first three is to be answered please…

Q: 3. Write any three differences between BJT and UJT

A:

Q: Use a rectifier with an intermediate taker to adjust current if the sine source voltage is 200…

A:

Q: A Copper-Constantan thermocouple (type T) is used to measure the temperature of a furnace. The…

A: Given: V0=3.972 mv Tref=15 C We need to find the temperature furnace.

Q: (7) Determine Is,Ic,IE, VB,and Vc in the following figure, where Bpc is 48. ww Rc >1.2KQ Vac 14.

A: Circuit diagram is given as,

Q: 1.Sketch the output voltage against time diagram for the values given in Q4 in the following.  Vref…

A: The circuit diagram is shown below, Where,Vref = 2 V,  Vs = 10 V  R1 = 1000 Ω R2 = 10,000 Ω

Q: Single phase half wave uncontrolled rectifier

A:

Q: Question 1 a) At the earthing point a heavy impulse current reaching the order of tens of kilo…

A: “Since you have asked multiple questions, we will solve the first question for you. If youwant any…

Q: A thermocouple has an output e.m.f. as shown in the following table when its hot (measuring)…

A:

Q: Q8. What is the difference between Zener breakdown and Avalanche breakdown?

A: The main difference between Zener breakdown and avalanche breakdown?

Q: d) Assume a bridge excitation of 5.0 volts; determine the bridge deflection voltage per 500 kg…

A: Given, R = 120 Ω GF = 2.02  Aluminum Column, d = 15 cm Aluminum Constant, E = 6.89 × 1010 N/m2 Area…

Q: Q4 Compare between Vametcan and Vazractca Vure = Vaameoretica V12 tractca)

A: Resistors, inductors and capacitors form an integral part of any electrical circuit. A source,…

Q: A transistor is used as a switch and the waveforms are shown below. The parameters are given as…

A: Given  Transistor as switch and waveforms as shown  Vcc=200 vVCE(sat)=1 vICS=100 AICEO=1 mArise time…

Q: show the deriviation of the eq and show the solution on how to come up to the final answer

A: It is given that:

Q: he condition of the power system gives the power flow solutions when the transient behavior of the…

A: The explanation is as follows.

Q: 91 kQ 18 ΚΩ • 330 ΚΩ VOSQ 1.1 k Vc 0-100 Vo LOSS V=-OV le E o 20 V 100 1.2 kQ

A:

Q: QUESTION 9: Find the change in load current with a change in collector voltage in a Widlar current…

A: The Widlar current source circuit diagram is shown below, The circuit parameters are as…

Q: a(t) +

A:

Q: Hence regulation for full load 0.75 leading conditions

A: The question is about finding voltage regulation of transformer.

Q: For a DC-DC Converter; The input voltage of the circuit is 12 V, the switching frequency is 1 KHz,…

A: A DC-DC converter has, Input voltage (Vin)= 12 volts Output voltage (Vo)= 48 volts Output Power…

Q: e. The maximum value of the load current is O 24 A O 33.9 A 20 A O 30 A

A: Single phase half wave uncontrolled Rectifier with pure resistive load 10ohm supplied using 240V…

Q: Q2. A small industrial user was fed from a 500 kVA, 11 kV/433 V transformer with a leakage impedance…

A:

Q: QUESTION 8: A Widlar current source has the configuration shown in the following figure. Assume the…

A:

Q: The initial delay of 30 degree replaced by 20 degree in three phase half wave controlled converter…

A: Choose the correct option If the firing angle of the first T1 Thyristor of half wave rectifier is 40…

Q: S 8(t) ejut dt =

A: According to the question, we need to solve

Q: 8.4-4 For the oscillatur circuit shown (a) Find the frequency of oscillation. (b) What is the ratio…

A: In simple words, we can say that an electronic circuit that can generate the sinusoidal wave is said…

Q: Define and differentiate HPLC and Reverse Phase LC

A: Brief description : In the above given question they want to have a definition and difference…

Z parameter

The Z-parameters that are the impedance parameters of a two-port network are defined by expressing the two-port voltages V1 and V2 in terms of two-port currents I1 and I2. The Z-parameters are calculated by open circuiting one of the two ports at a time henceforth they are called open-circuit impedance parameters.