In the power system whose single line diagram is shown below, the line cross section is 95 mm2, the intrinsic conductivity coefficient is 34 m/ohm.mm2 and the inductive reactance of the line is given as 0.4 ohm/km. According to these values; a) Calculate the active, reactive and visible components of the currents passing through each line segment. b) Find the location and value of the largest voltage drop.

In the power system whose single line diagram is shown below, the line cross section is 95 mm2, the intrinsic conductivity coefficient is 34 m/ohm.mm2 and the inductive reactance of the line is given as 0.4 ohm/km. According to these values; a) Calculate the active, reactive and visible components of the currents passing through each line segment. b) Find the location and value of the largest voltage drop.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

in the circuit shown below. Determine the following A)Vs (at the secondary) B)Vout(across R) C)Vrip (ripple Voltag) D) VDC full wave rectifier E) PIV(peak inverse Voltage) V1 C1 100µF 240V / 50HZ R1 104µF 1k T1 30:1
Give the meaning of each acronym of solid state devices. Also sketch the schematic symbol for each device. SUS Shockley diode D-MOSFET JFET SCR DIAC THYRISTOR Device TRIAC 1. 3. 4. 6. 8. 10. 12. 14. Symbol 2. 5. 7. 9. 11. 13. 15. Meaning No entry
A circle with diameter D in 1000 D mil d mil has an area of cmil. Fill in the Blank.
A full wave rectifier circuit has input voltage 220 Vrms, the average output voltage (DC voltage) is Select one: O a. 198 V O b. 99 V O c 21 V O d. None of the above e. 10.8
FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to c 20:5A L VI-DC20V 220V omsh T 0.01 F 0.02 F 0.0167 F None of the above euer
In a rectifier circuit , DC output voltage and RMS output voltage is 0.3 V & 0.55 V respectively. The form factor of this circuit is a. 3.67 b. 0.55 c. 1.35 d. 1.83
what is the schematic diagram of TP4056 Micro USB battery lithium 18650
For Fixed Bias Configuration Solve for Ib, Ic and le. Atleast 2 decimal place. Be mindful of units. Assume Ic is not equal to le. 4 RC 15002 RB VCC 20V 90A/A 100k2
The input to a full-wave rectifier is 40 V AC (RMS). The load resistor is 10 ohms. The DC voltage at the output is: O A. 27 V O B. 18 V O C. 36 V O D. None of the other choices are correct O E. 21 V
Determine the currents 1, 12 and 13 respectively for the network shown. Use simplified model for the diodes. D 3.3 k2 R2 E = 20V D2 R1 5.6 kN 10.52 mA, 17 mA, 20mA 1.004 mA, OmA, 7.44 A O 0.514 mA, 2.62 mA, 0.799 mA O 3.32 mA, 0.212 mA, 3.108 mA
89. If the ripple voltage in a full-wave rectifier is 25 V at a load current of 60 mA, its value at a load current of 120 mA will be (i) 50 V (ii) 25 V (iii) 100 V (iv) 12.5 V