What is a reasonable minimum width to assume for an interior concrete beam that has four #8 bars as its longitudinal reinforcing?

Q: What is the minimum area of tension reinforcement in beams when Fe 415 is used?

A: Given, Fe 415 is used, The minimum area of tension reinforcement in beams =? fy=415 MPa.

Q: For the frame and loading shown, determine the components of all forces acting on member ABC. 1.2 m…

A:

Q: What is the rod reading at the arrow? 4 3 7 3 =6

A: Rod reading:- The number on the rod is level with the height of the die-observing instrument.…

Q: 6-83. Determine the force in members FD and DB of the frame. Also, find the horizontal and vertical…

A:

Q: 6-30. Determine the force in members CD, HI, and CH of the truss, and state if the members are in…

A: Given: Determine the force in member CD, HI and CH of the truss ?

Q: 2. Determine the internal forces of the beam shown in figure by drawing the shear force and bending…

A: Determine the internal forces of the beam shown in figure by drawing the shear force and bending…

Q: The soil layers below have a cross section of 100 mm x 100 mm each. The permeability of each soil…

A:

Q: Determine the total pressure on a circular plate of diameter 1.5 m which is placed vertically in…

A: Given Diameter of plate d=1.5 m, Distance of center of plate from free surface of water h¯=3 m, It…

Q: 4. Given two Orthographic views of an object, construct an Auxiliary view of the indicated ( —P)…

A: Auxiliary view

Q: A metal shaft of solid circular section rotates at 160 rpm and is subjected to a torque of 1500 Nm.…

A:

Q: There is a natural sandy soil. The density ρ is 1.77 g/cm3, moisture content w is 9.8%, and specific…

A: Answer  We are given  density = 1.77 g/cm3  moisture content w = 9.8% Specific gravity of soil Gs =…

Q: Question 1 A vehicle is moving at a speed of 80 kph along an incline surface having a slope of 4%.…

A: V=80kph To find braking distance

Q: 2-21. Determine the reactions at the supports A and B of the compound beam. There is a pin at C. 6 m…

A: A beam is given as shown in figure and it has been asked to determine support reactions. Please…

Q: roblem 3. Beam ABCD shown below has a pinned support at A and a roller support at C. For he given…

A: To draw SFD and BMD

Q: Problem 3 The bar CBA is axially loaded by force P at end A and by force Q at section B. The entire…

A: Given : E = 70 GPa Determine the magnitude of force Q so that deflection at end A is zero.…

Q: Q- A fine-grained soil has 60% (by weight) silt content. The soil behaves as semi-solid when water…

A: Given data- Silt content SC=60%, Liquid limit LL=40%, Plastic limit PL=28%, To Find- The value of…

Q: Problem- A circular pipe has a diameter of 1m, bed slope of 1 in 1000, and Manning's roughness…

A: Given- Diameter D=1m, Bed slope s=1 in 1000, n=0.01, Flow depth y=0.5 m, It is needed to find the…

Q: In the figure, aluminum [E = 69 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

A:

Q: A mild steel bar is in two parts having equal lengths. The area of cross-section of Part-l is double…

A:

Q: A -8 m- B C Hinge D E F G Hinge -6 m--4 m--4 m--3 m--3 m-- -8 m- H

A: Given beam

Q: From the given figure, compute the maximum deflection and rotation at the free end of the cantilever…

A: Given: 1. Load=uniformly distributed load(W)=12kN/m2.2. Length of the beam AB L=10m.3. Modulus of…

Q: Question 89 What is the shear stress at the neutrsl axis in a beam of isosceles triangular section…

A: Given :- Base width, B = 40 mm Height, h = 20 mm Shear Force, F = 3 kN = 3000 N To Determine :- The…

Q: Calculate the force and moment reactions at the bolted base O of the overhead traffice-signal…

A: Mass of traffic signal=25kg Mass of member OC=70kg Mass of member AC=64kg To find reaction at point…

Q: e velocity component in the y-direction, vy?

A: This question is from fluid mechanics subject

Q: determine the deflection point D of the beam shown bellow by the virtual work method Note:The real…

A:

Q: The angle of intersection of a circular curve is 36° 30'. The external distance and speed are 39.43…

A:

Q: Determine the forces in members BE and CE of the loaded truss. The forces are positive if in…

A: Given, BC ¯=CD¯

Q: A 18-kN-m torque T is applied to the solid cylinder made up of a hollow cylinder and an inner core…

A: Solution is attached below

Q: Problem 3. The beam AB has a negligible mass and thickness and is subjected to a triangular…

A: Given : P = 150 N   Determine the two coefficient of static friction at B and C ?

Q: lar shaft has an outside diameter of 5 inches and inside diameter of 4 inches. What is the polar…

A:

Q: Situation 3: Consider the following shrinkage limit test using mercury. Mass of moisture can: 16.5 g…

A: At first we will find water content , then dry density, volume etc. Explanation given below.

Q: 7-65. Draw the shear and bending-moment diagrams for he beam. 500 N/m

A: Given Data : We are asked to draw the shear and bending moment diagrams for the beam?

Q: Check slenderness for local buckling of a W12X65 from the AISC Steel Construction manual.

A: Check slenderness for web and flange as per AISC Steel manual. W12X65 section.

Q: 9. Given the following tabulated data for a close traverse. Line 1-2 2-3 3-4 4-5 5-1 Length 445.66…

A: Multiple Sub- parts As per our company guidelines we are supposed to answer only first 3 sub-parts.…

Q: only Find Neutral Axis (NA). please in detail.

A: In this question, We solve only Neutral axis distance as per requirement of question. This question…

Q: 1. A cable supports a load of 50 kg/m uniformly distributed with respect to the horizontal and is…

A: Given data  Find maximum tension and minimum tension in cable.

Q: 83. Determine the force in members FD and DB of the me. Also, find the horizontal and vertical…

A: To find force in member FD,BD

Q: The directions observed from a satellite station 5, 70m from a triangulation station C, to the…

A: Given data:- θ=71°32'54''α=301°16'15"a=AC=2750 m=2.75 kmb=BC=4165 m=4.165 kmd=70 m Assume angle…

Q: Derive the ff. From Reactions, Moments, Slope A & B, and Deflection. A W L/2 L/2 B B

A:

Q: ete the of the figure below. and mor 28 KN alagram

A: GIVEN

Q: Determine the force in member AB, AF, BC, BE, BF, CD, CE, DE, EF, and FG and state if the member is…

A: Determine the force in member AB, AF, BC, BE, BF, CD, CE, DE, EF, and FG and state if the member is…

Q: The superelevation needed on a horizontal circular curve of 180 m radius for a design speed of 65…

A:

Q: An Accessible Route can be broken and restarted if the break in accessiblity is less the 30 feet and…

A: As part of an accessible route, all walkways, halls, corridors, aisles, skywalks, tunnels, and other…

Q: The following data were obtained by stadia measurement. If the height of the instrument is 1.362m…

A: K=96.8m C=0.3m S1=2.216m S2=1.06m

Q: Calcualate the deflection and slope at A and C of the concrete beam in the figure using virtual work…

A:

Q: A rectangular plane surface 2 m wide and 3 m deep lies in water in such a way that its plane makes…

A: Given: Size of Plate =2m wide x3m deep from the surface of the water. The angle between the plate…

Q: A glulam beam is manufactured with a depth of 450 mm and a 12% moisture content. Assuming common…

A: Given:- d=450mm moisture content=12% moisture content increased=40% To find:- new depth of beam

Q: Problem-7. In a region with magnetic declination of 2 °E, the magnetic Force Bearing FB) of a line…

A: Given data- Magnetic declination- δ=2oE,FB=N79o5'E, To Find- The true FB of line AB.

Q: What is the equation to convert the Azimuth below to a Bearing? Οξε οτε οτε 008 067 087 017 097 Osz…

A: Azimuth to bearing

Q: 1. Determine the reaction at the supports for the beam shown. Take E = 200 GPa and I = 90x10* m* 200…

A: As per our company bartleby guidelines we can solve one question per attempt (i.e., first question)…

Braced cuts

The braced cut is a method of providing lateral support to the soil in foundation trenches, to prevent the trenches from deformation by the caving in of soil and resisting it from moving laterally. During shallow excavation in firm soil, generally, slopes are provided to resist the caving in of soil. During shallow excavation in soft soil and deep excavation, the chances of caving in of soil increase. Hence, it becomes necessary to make a provision to resist the deformation of trenches due to caving in of soil. The braced cut is the method used for such conditions. The excavation using braced cuts is a bit uneconomical as compared to the traditional open-cut excavation method but provides better safety than the cut excavation method.