Problem 3. The beam AB has a negligible mass and thickness and is subjected to a triangular distributed loading. It is supported at one end by a pin and at the other end by a post having a mass of 50 kg and negligible thickness. Determine the two coefficients of static fraction at B and at C so that when the magnitude of the applied force is increased to P = 150 N, the post slips at both B and C simultaneously. 800 N/m

Problem 3. The beam AB has a negligible mass and thickness and is subjected to a triangular distributed loading. It is supported at one end by a pin and at the other end by a post having a mass of 50 kg and negligible thickness. Determine the two coefficients of static fraction at B and at C so that when the magnitude of the applied force is increased to P = 150 N, the post slips at both B and C simultaneously. 800 N/m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rigid beam ABC is supported by a pin connection at C and by steel rod (1), which has a diameter of 7 mm. If the normal stress in rod (1) must not exceed 215 MPa, what is the maximum uniformly distributed load w that may be applied to beam ABC? What is the allowable force in road (1)? Use dimensions of a = 350 mm, b = 700 mm, and c = 525.0 mm.
la. Draw the V and M Diagram 10kN/m 12KN/m 5kN/m 3kN-m 3m 2m 2m 3m 1b. Compute for the maximum bending stress of the given beam if the cross sectional area is: 30mm 30mm 60mm 1.c. Compute the flexural stress at 3m from the hinge if the cross sectional area is: Equilateral Triangle 100mm
3.75 نقطة )نقاط( السؤال 5 The beam is supported by a pin at A and a short link BC. If P = 5 kN and the diameter of the pin at C is 8 mm, determine the factor of safety against shear stress of pin .C assuming 800 MPa 2P |0.5,m 1 m-1.5 m -1.5 m- 4P 4P P. 0.5 m| 30 B 1.269 1.257 1.322 O 1.462 O
Please answer asap. thank you so much..
1. "ll zain IQ Qz 5 torsion.p.. Strength of materials Qz The steel shaft has a diameter of 50 mm and is fixed at end A and turn free at end B. If it is subjected to the couple, determine the maximum shear stress in regions AC and CB of the shaft. G = 75 GPa. 3 kN 3 kN 400 mm 50 mm 50 mm 600 mm
Asap pls
A cantilever beam has a span of 2 m. and having a flexural rigidity of 40000 kN.m². At the free end of the beam there is a spring with a clearance of 200 mm below the beam. Spring constant is 252 N/m. #13 0.20 m #14 Find the force acting on the spring after a concentrated load of 800 kN is applied at the force end. #15 Compute the moment at the fixed end. Compute the deflection of the spring after a concentrated load of 800 KN is applied at the free end of the beam. P=800 KN
5-83 The A-36 steel shaft is made from two segments: AC has a diameter of 0.5 in. and CB has a diameter of 1 in. If the shaft is fixed at its ends A and B and subjected to a uni- form distributed torque of 60 lb in./in. along segment CB, determine the absolute maximum shear stress in the shaft. 5 in. 0.5 in. 20 in. 60 lb-in./in. 1 in. B Prob. 5-83
The lap joint is fastened with four ¾ inch diameter rivets. The working stresses are 14 ksi for the rivets in shear and 18 ksi for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets.
1. A frame held taut by a rope connected at D and E, is pin connected at B. If 1500 N is perpendicular to the member AB, determine the tension on the rope and the horizontal and vertical components of forces at B. Assume roller connection at A. 2000 N 2 m Fim--1 m- 1500 N 2 m 2 m 45° A
Subject:
-2.4m- 8 mm 200 mq 8 mm 250 mm 8mm The steel beam has the cross-sectional area shown. The beam is loaded as shown with the intensity of the distributed loading w=70 kN/m. Determine the absolute maximum bending stress in the beam in MPa.