Water is going to be pumped between point A and B as shown in Figure below. Calculate the maximum h for the flow rate of 90 L/s and pipe diameter of 0.3 m. Hint: minimum total pressure at point B must be above vapor pressure. B h

Water is going to be pumped between point A and B as shown in Figure below. Calculate the maximum h for the flow rate of 90 L/s and pipe diameter of 0.3 m. Hint: minimum total pressure at point B must be above vapor pressure. B h

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: local losses at points A, B, C, and D for pipes in series shown in Figure 1. Assun fully turbulent…

A: According to given data .

Q: B: Answer with True (T) or False (F). 1- Manometer and Piezometer used for determine large discharge…

A: As per guidelines we need to answer only first 3 subparts of question so please repost rest…

Q: 8) A private water utility purchases 10,000,000 kilowatt-hours of electricity per year for pump…

Q: Pump inflow 2. Draw the HGL for the system shown below. The pump flow at A is 100 L/s with a 550 kPa…

A: Solution for this question is provided below ⬇️...Explanation:

Q: If liquid with viscosity equal 5.16*10" m/sec, flow in 60 m long square duct with side dimension 50…

A: step 1-

Q: Consider the water distribution network. Given the information below, find the flow rate between A…

A: Solution So, in first iteration: Assume flow through AB = Q1 = 0.03946 Q2=Q3=Q4 = 0.03946 For…

Q: In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000…

Q: A 30 cm diameter pipe is connected by a reducer to a 10 cm diameter pipe. Points 1 (on the 30 cm…

A: Diameter =30cm pressure at 1 =250 kPa Discharge Q1=Q2=Q=0.03 m3/sheadlossHL=20rmVelocity…

Q: Problem 3 Water needs to flow from one large tank with water surface elevation of 120 m to another…

Q: Problem #12 Water 118 -diameter nozzle Determine the discharge in the pipe (in cfs) and the pressure…

A: Pipe arrangement is given in the figure as shown above and it has been asked in the question to…

Q: The pressure at the 2nd floor faucet in the residential building is estimated to be about 45 psi for…

Q: 2. Water at 25 "C in the 60 mm diameter duct. Compute the flow rate and direction of the flow…

A: Given data: 25o C Length = 50 m diameter = 60 mm

Q: A residential area located in an urban zone of Basrah governorate is served by the triangular pipes…

Q: Prob. # 3 (a): A 90° horizontal reducing elbow carries a flow of 12 cfs (i.e., cubic feet per…

Q: Problem #2 Water 11 M diameter sin -diameter nozzle Determine the discharge in the pipe (in cfs) and…

A: Given : Determine the discharge in the pipe and pressure at point B ?

Q: A 30 cm pipe is connected by a reducer to a 10 cm pipe. Points 1 and 2 are at the same elevation.…

A: d1 = 30cm d2 = 10cm P1 = 207KPa Q = 30L/s H = 2.5m

Q: A pipe carries a flow of 5.17 cfs of oil (SG = 0.877). At one diameter is 6 inch, the pressure is…

A: Flow of oil in the pipe, Q = 5.17cfs , Specific Gravity of oil = 0.877 , d1= 6 in , p1= 13.2 psi =…

Q: 10.76. Experiments show that in the aging of pipes (a) the friction factor increases linearly with…

A: According to our bartleby guidelines, we can provide one question answer at one time sorry for the…

Q: Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as…

A: Given that: Vapour Pressure of water: Pv=2.25kPaAtmospheric Pressure, Patm = 100 kPaγwater =9810…

Q: Determine the quantity of flow Q at the outflow end of the pipe shown in figure 4-6 of your book…

A: Elevation of the center of pipe (H1) = 513 feet Elevation of the surface of the reservoir(H2) = 537…

Q: In the parallel system shown, pipe 1 has a length of 3000 ft and 20-inch in diameter. Pipe 2 is 5000…

A: Solution:

Q: L=4000ft D=16 inch A B L=2000ft D=12 inch

Q: Nozzle

A: To calculate pressure head at point 2. Applying Bernoullis equation at point 2 and exit. Note that…

Q: A horizontal pipe gradually reduces its diameter from 300 mm at point A to 100 mm at point B. The…

A: dia at A(DA)= 300mm=0.3marea at A(AA)=dia at A(DB)= 100mm=0.1marea at B(AB)=pressure at A(PA)= 100…

Q: water is being delivered at a rate of 2000 gpm for a reservoir to a subdivison below resvoir…

A: Reservoirs are artificial lakes where water is stored. The most common method of forming reservoirs…

Q: Q2) For the pipe system shown in the figure, the flow rate is 0.00085 m³/s & v-1.14*10 m²/s,…

A: To Determine Pressure at point 1, P1

Q: Water flows from reservoir A to a turbine and then discharges into tailrace B, as shown in the…

A: To Determine The horsepower being generated by the turbine.

Q: The three water-filled tanks shown in the figure below are connected by pipes as indicated. If minor…

A: given data,Find discharge at Adischarge at Bdischarge at C

Q: Water flows from a tank through a 23 cm diameter steel pipe. Determine (a) the discharge of water,…

Q: For the three reservoir system shown, reservoir A supplies water to reservoir B and C at 10 li/s and…

Q: The pressure at the 2nd floor faucet in the residential building is estimated to be about 43 psi for…

Q: Compute the friction factor for the smaller pipe when two smooth pipes are connected in series where…

Q: Pipe A 600 m 0.15 m f-0.02 Pipe C 1200 m 0.2 m 1-0.024 Pipe B 480 m 0.1 me f-0.032 60 m 36 m 15 m…

Q: Oil is pumped from a lower tank to an elevated spherical tank. The lower tank is vented to the…

A: Given, P2 = 240 kPa ρoil = 920 kg/m3

Q: Q6. Absolute vapor pressure of water siphoned is 2.25 kPa. Water is extracted from a reservoir as…

A: Given that: Vapour Pressure of water, Pv = 2.25 kPaDiameter of pipe, D = 16 cm = 0.16 mPatm=100…

Q: Situation 7: From reservoir A whose water surface elevation is 225 m. Water is pumped through a 350…

A: Given:- Water is pumped through a 350 mm diameter pipe across a valley.- Elevation of reservoir A…

Q: Water enters a pipe of length 10ft and diameter 2 inch with a mass flow rate of 150 kg/min. The…

A: Given: Length of pipe, L = 10 ft Diameter of pipe, D = 2 in Mass flow rate, m = 150 kg/min Density,…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

Water is going to be pumped between point A and B as shown in Figure below. Calculate the
maximum h for the flow rate of 90 L/s and pipe diameter of 0.3 m. Hint: minimum total pressure
at point B must be above vapor pressure.
B
[]
+H

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Water is following steadily through a 50 m long section of a horizontal 5-cm diameter stainless steel pipe. The water temperature is 15°C and the flow rate is 9 L/s. Determine: a.) The pressure drop over the pipe length [kPa]. b.) The head loss [m]. c.) The pumping power needed to overcome the pressure drop (assume a pump efficiency of 67%) [kW]. 9 L/s 5 cm 50 m
Determine the division of flow and head loss from A to B, if the given f=0.010 for all pipes. Note that the total flow is 10 cfs. L=4000ft D=16 inch B L=2000ft D=12 inch
asnwer asan with neat solution thank youGiven the figure below, (a) determine the flow rate in the siphon shown. Diameter of the pipe is 2.5cm.(b) Determine the pressure at point B.
Due in 2 hrs Please show figure thanks! No figure no credit for us in school.
please answer quickly
Data measured during tests of a centrifugal pump at 2750 rpm are Parameter Inlet, Section Outlet, Section (2) Gage pressure, p (kPa) Elevation above datum, z (m) 120 500 2.5 Average speed of flow, V (m/s) 2.5 3.5 The flow rate is 15 cu.m./hr. and the torque applied to the pump shaft is 85N.m. Evaluate the total dynamic heads at the pump inlet and outlet, the hydraulic power input to the fluid, and the pump efficiency. Specify the electric motor size needed to drive the pump. If the electric motor efficiency is 85%, calculate the electric power requirement
2.Water (ρ = 1000kg / m3, μ = 10-3Pa.s) flows at a speed of 1.6m / s (Reynolds number Re = 0.8 105) in a pipe whose diameter is to be determined.
7. Barometeric pressure is 101.3 kPa and vapor pressure of water is 32.4 kPa. Calculate the elevation (in meters) of the tubing end 3 for maximum flowrate through this pipeline. Also sketch the energy line, EL (color red) and the hydraulic grade line, HGL (color blue) on the drawing for this situation. El. 34 Water 150 mm d EI. 30.5
Compute the head loss in a 5 inches pipe if it is necessary to maintain a pressure of 36.5 psi at a point upstream and 7 ft below where the pipe discharges water into the atmosphere at the rate of 1.963 cfs. Show the diagram.
The commercial steel tube is then 100 m long and0.4 m in diameter. Calculate the height of the tower h, if the flow speed for7.95 m / s. Consider that losses are negligible and that losseswater temperature is 4 ° C
Subject : Fluid mechanics Give me all answers.. Urgent