Data measured during tests of a centrifugal pump at 2750 rpm are Parameter Inlet, Section O Outlet, Section 2 Gage pressure, p (kPa) Elevation above datum, z (m) 120 500 9 2.5 Average speed of flow, V (m/s) 2.5 3.5 The flow rate is 15 cu.m./hr. and the torque applied to the pump shaft is 85N.m. Evaluate the total dynamic heads at the pump inlet and outlet, the hydraulic power input to the fluid, and the pump efficiency. Specify the electric motor size needed to drive the pump. If the electric motor efficiency is 85%, calculate the electric power requirement

Data measured during tests of a centrifugal pump at 2750 rpm are Parameter Inlet, Section O Outlet, Section 2 Gage pressure, p (kPa) Elevation above datum, z (m) 120 500 9 2.5 Average speed of flow, V (m/s) 2.5 3.5 The flow rate is 15 cu.m./hr. and the torque applied to the pump shaft is 85N.m. Evaluate the total dynamic heads at the pump inlet and outlet, the hydraulic power input to the fluid, and the pump efficiency. Specify the electric motor size needed to drive the pump. If the electric motor efficiency is 85%, calculate the electric power requirement

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Subject hydraulics: Consider FIGURE R1M—3. Determine the discharge and the pressure head at A and B given a pipediameter of 200 mm and the exit diameter to be 150 mm. Neglect losses of head.
the unknown fluid? Express your answer in Ib/ft³. TEST 1 Fall 2021 5. For the configuration shown in the figure below what must be the value of the unit weight of the upkontiguration shown in the fiqure below what must be the value of the unit weight of ie unknown fluid? Express your answer in Ib/t. [Max. 10 Points] Open Water 49 in 5.5 in 3.3in JAknown 1.4tin
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the 2 gage pressure readings is 28 kPa. a) Determine the flow in m^3/s neglecting head losses. (Please round-off final answer to four decimal places) * b) Working from Bernoulli’s equation, determine the difference in level (in millimeters) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil. (Please round-off final answer to a whole number)
A venturi meter with a throat diameter of 100 mm is fitted in a vertical pipeline of 200 mm diameter with oil of specific gravity 0.88 flowing upwards. Two pressure gauges are fitted at tapping points, one at the throat and the other in the inlet pipe 320 mm below the throat. The difference between the 2 gage pressure readings is 28 kPa. (a) Determine the flow in m^3/s neglecting head losses (b) Working from Bernoulli's equation, determine the difference in levels (in mm) between the two limbs of a mercury manometer if it is connected to the tapping points and the connecting pipes are filled with the same oil Draw illustrations Use 3 decimals
A pump is to deliver 80 GPM of water at a density of 61. 83lb/ft cubed with a discharge pressure of 150 psig. Suction pressure indicates a 2 HG vacuum. The diameter of the suction and the discharge are 5 in. and 4 in. respectively. The pump has an efficiency of 70% while the motor efficiency is 80%. Determine the (a) water horsepower of the pump (b) bhp of pump motor (c) power input to drive the motor.
Q10.8 Hydraulic conductivity of an aquifer is known to be 8 ft/day, and its dimensions are estimated to be 40 ft thick and 18,000 ft wide. Two test wells drilled one mile apart in the direction of flow encountered the water table al clevations 5,030 t and 5,050 fL. Question: How many gallons of water flow through the aquifer per day? (To at the front of this manual.) o convert 'o gal, see page We've updated our read aloud featur Give it a try here. A Aa
Water flows through a 300mm diameter pipe at a velocity Of 3.00 m/s. Determine the weight flow rate in N/s. Do not write the unit. You will only jnput the numerical answer in the space provided. Unit of the Correct Answer: N/s O 9810.000 O 2,080.284 O 8829.000 1202.284
Question 1: For the setup shown in the figure: H = 20 m f = 0.0012 f = 0.0012 D = 250 mm D = 80 mm L = 50 m L = 50 m f = 0.001 D₁ = 150 mm L = 100 m A. Calculate Q in the 150 mm-diameter pipe B. If the NPSHR of the pump is 3 m. Is it feasible to use the pump? You can use: Patm-101 kN/m², and Pvapor = 3.17 kN/m² H₂ = 10 m Pump Q f = 0.0012 D=80 mm L = 50 m Q₁ = 0.2
Chow, Ven Te, Handbook of Applied Hydrology, McGraw-Hill, 1964. FRICTION FACTOR f 08 07 Find the Q and V at the exit. Include friction losses (e.g., REAL fluid case) but ignore minor losses. Absolute Roughness e = 1.5 mm (See Moody Diagram next sheet) FE Manual Moody Diagram 06 .05 .04 03 02 01 0.1 0.2 CLAMINAR CRITICAL FLOW ZONE LAMINAR FLOW f-64/Re 0.4 0.6 0.8 1 6 8 10³ 2 TRANSITION ZONE CRITICAL Re 2 GLASS, DRAWN BRASS, COPPER, LEAD COMMERCIAL STEEL, WROUGHT IRON ASPHALTED CAST IRON GALVANIZED IRON CAST IRON CONCRETE RIVETED STEEL -0.03 CORRUGATED METAL PIPE -0.2 LARGE TUNNEL, CONCRETE OR STEEL LINED 0.002 -0.004 BLASTED ROCK TUNNEL 1.0 <-2.0 4 6 8 10 ZIN FI SMOOTH 410.0 feet 0.003 0.1 0.0001 -0.0003 0.0002 -0.0006 0.0002 -0.0008 0.0006 -0.003 0.001 -0.01 2 8" Dia. VALUE OF VD FOR WATER AT 60°F (V IN FPS, DIN INCHES) 4 6 8 10 2 4 6 8 10² 2 4 6 8 10³ 50' COMPLETE TURBULENCE ROUGH PIPES SMOOTH PIPES 4 6 8 105 2 4 6 8 10⁰ VD REYNOLDS NUMBER Re= V 2 3 00002 00001 6 8 10 372.5 feet 2 4 6…
Point A in the suction pipe is 1 m below the pump. It is mounted with anopen manometer which reads a vacuum of 20 cm of mercury. The pipe is10 cm in diameter and the flow is 35 liters/s of water. Compute the totalenergy at point A with respect to a datum through the pump.
SN=23 SUPPLEMENTARY QUESTION The figure shows two reservoirs connected by a pipe. The discharge rate in the pipe is known to be equal to SN/100 (m/s) (where SN is the sum of your student number). Calculate the height of the second reservoir (H2), and the pressure head, velocity head and elevation head at point 3 (mid-point of the pipe). Hi-300 m Ha datum A SN/1000 L- 100 x SN (m) D 0.3 m
a. Calculate the pump head b. Plot the EGL and HGL for the system