Using the general bearing capacity equation, what is the factor of safety for a foundation system that includes a 5 ft square footing at a depth of 4 ft carrying 120 kips at a 10 degree incline from vertical. c’=0. φ= 28º. γ = 100 lb/ft3. The water table is deep and is not expected to affect foundation performance.

Using the general bearing capacity equation, what is the factor of safety for a foundation system that includes a 5 ft square footing at a depth of 4 ft carrying 120 kips at a 10 degree incline from vertical. c’=0. φ= 28º. γ = 100 lb/ft3. The water table is deep and is not expected to affect foundation performance.

Principles of Foundation Engineering (MindTap Course List)

9th Edition

ISBN:9781337705028

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter10: Mat Foundations

Section: Chapter Questions

Problem 10.2P

See similar textbooks

Similar questions

A square column foundation has to carry a gross allowable load of 1805 kN (FS = 3). Given: Df = 1.5 m, =15.9 kN/m3, = 34, and c = 0. Use Terzaghis equation to determine the size of the foundation (B). Assume general shear failure.
A shallow continuous foundation is to be constructed on a soil under the ground'. surface as shown in the figure below. Determine the gross allowable bearing capacity with a factor of safety FS = 3. All dimensions in meter. II. Comment of the effect of placing the footing at the ground surface (i.e. Dr= 0) on the computed allowable bearing capacity. Take Neg as 5. 2.8 1.4 I G.S. 30 1.4 Yson = 17.7 kN/m = 30° C= 40 KN/m?
A foundation is 3 mx 2 m in plan. Given: Df= 1.5 m, o'= 25°, c'= 70 kN/m². With General Bearing Capacity equation and FS = 3 assmuming general shear failure in soil, determine the net allowable load that the footing can carry. a) NOTE: Due to drought, groundwater level has been lowered down to a depth of 1.5m from the ground surface. b) Net allowable load that the footing can carry using general bearing capacity equation and F.S.=3 assuming general shear failure in soil. c) Ultimate bearing capacity (qu) using prakash and saran theory with eB=0.3m and eL=0.5m. y = 17 kN/m 1 m 1.5 m Groundwater level 3 m x 2 m Yut = 19.5 kN/m
The square footing shown below must be designed to carry a 2400 KN load. Use Terzaghi's bearing capacity formula and factor of safety = 3. Determine the foundation dimension B in the following two cases: 1. The water table is at Im below the foundation (as shown). 2. The water table rises to the ground surface. 2400 kN O = 32° C = 50 kN/m? Yd = 17.25 kN/m³ 2 m 3m B Ys = 19.5 kN/m³
2. A medium dense sand is proposed to support a square foundation having a width and length of 5 feet as shown below. The bottom of the footing is 2.5 feet below the ground surface. The water table is 4 feet below the bottom of the footing. Using a factor of safety of 3, what is the allowable bearing capacity of the proposed footing? Gs= 2.6 e = 0.5 Ø = 35° 5 ft d = 4 ft
Subject: Principles of Foundation Design (Use NCSP) A rectangular footing is to be used to support a 300x400 (*400mm side is parallel to the long dimension of the footing) column loaded with 420 kN dead load and 540 kN live load. One side of the footing is 4.0m. Use effective soil pressure of 70 kPa. f'c=35 MPa and fy=420 MPa. Use minimum steel ratio for longitudinal bars as 0.0018. •Calculate the required thickness of the footing (mm) based on wide beam shear. db=16mm. Size of footing should be multiples of 10mm (Answer: 300) •Calculate the required thickness of the footing based on two-way shear. db=16mm (Answer: 430) • Calculate the required number of 16mm bars along long direction. . Use the governing thickness based on shear requirements. (Answer: 22)
It is planned to construct a rectangular foundation with base dimensions of 8 * 14 m (B* L) on the construction site with the ground profile as in the figure. Accordingly, if the YASS descends 9 m, what would be the change in the final bearing capacity of the ground? Note: Make your calculation using the Terzaghi bearing capacity formula as the safety factor of 3 0m c=18 kPa, -18° Y=20 kN/m³ Y-21,8 kN/m³ 1.5 m SM H e=0.67 2.7 m GW 12 m c=8 kPa, -23° e=0.23 Yo=22 kN/m³ Y-23,2 kN/m³
Calculate the ultimate bearing capacity of a 2 m wide strip foundation embedded 2 m below the ground surface in soil with a saturated unit weight of 20 kN/m3. Dry unit weight of 18&N /m The water table is at the foundation level. The friction angle is 30°. 1. Calculate the bearing capacity of the foundation. 2. The design load on the foundation is 500 kPa. Comment on the safety of the foundation.
A rectangular footing with width (B) = 6 ft and length (L) = 8 ft is subjected 5b) (P) = 75 k (shown below). The footing is 3 ft thick and flush with the ground surface. Assume x = 0.75 ft and y = 0.5 ft and solve for the eccentricity in the B direction (eB) and the eccentricity in the L direction (eL). Is this foundation adequately sized to resist overturning (i.e., is it in full bearing or partial bearing)? If it is in full bearing, compute the maximum and minimum pressure under the footing. an eccentric load Top View L y В
A strip footing is to be designed to support a dead load of 500 kN/m and an imposed load of 300 kN/m at a depth of 0.7 m in a gravelly sand. Characteristic values of the shear strength parameters are c' = 0 and ϕ' =40˚. (a) Determine the required width of the footing if a factor of safety of 3.0 and assuming that the water table may rise to foundation level. (b) Would a foundation of that width satisfy the bearing resistance limit state? The unit weight of the sand above the water table is 17 kN/m3 and below the water table the saturated unit weight is 20 kN/m3.
The square footing shown below must be designed to carry a 2400 KN load. Use Terzaghi's bearing capacity formula and factor of safety = 3. Determine the foundation dimension B in the following a. If the water table is well below the foundation level cases: b. If the water table is at the foundation level c. If the water table is at the surface 2400 kN + = 32° C = 50 kN/m² Ya = 17.25 kN/m³ 2m 3m Y, = 19.5 kN/m³
A 300 mm x 400 mm column is to be supported by 530 m thick square footing @ its center. Service DL = 597 kN, service LL = 676 kN, CC to bar centroid is 90 mm, fc' = 24.7 MPa and fy = 414 MPa. Consider the weight of the footing and soil to be 16.04% of the dead load. SBC = 160 kPa %3D 300 400 300 Determine the required number of 20 mm bars parallel to the critical side. Note: Present the width (B) in multiples of 100 mm.