Using superposition, find the value of io if voltage source at the left is 10, angle -30 degrees V, and current source is 2, angle zero degrees. A total of three sources will be considered, separately. The 24 Volt source is DC. When this source is acting alone, the capacitor will be open-circuited. 24 V 10 2 H ww| ell

Using superposition, find the value of io if voltage source at the left is 10, angle -30 degrees V, and current source is 2, angle zero degrees. A total of three sources will be considered, separately. The 24 Volt source is DC. When this source is acting alone, the capacitor will be open-circuited. 24 V 10 2 H ww| ell

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

Incandescent lighting of 500 W is connected in parallel with an inductive load. A clamp-on ammeter reveals a total circuit current of 7 A. What is the inductance of the load connected in parallel with the incandescent lights? Assume a voltage of 120 V and a frequency of 60 Hz.
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
A pure capacitive circuit is connected to a 480-volt, 60-Hz power source. An ammeter indicates a current flow of 24 amperes. The circuit current must be reduced to 16 amperes by connecting a second capacitor in series with the first. What is the value of the existing capacitor? What value capacitor should be connected in series with the original capacitor to limit the circuit current to 16 amperes?
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
AC Circuits Sine-wave generator f- 25 kHz V₁ = 3.0 V VR 888 100 mH Figure 6-Test Circuit 3. Using a two-channel oscilloscope, measure the peak-to-peak voltage VR across the resistor and the peak-to-peak voltage VL across the inductor. Measure the voltage across the inductor using the difference technique described in a previous experiment. Record the voltage readings in Table 2. VL 10 k 1 XL Table 2- Measured and Calculated Values (f = 25 kHz) ZT
Two 10 uF capacitors have been connected in parallel across a 230 V 50 Hz AC supply. The current drawn from the supply will be approximately: Select one: a. 1.44 A b. 0.36 A c. 11.5 A O d. 23.0 A
A 22-k resistor and a 0.02-F capacitor are connected in series to a 5-V source. How long will it take the capacitor to charge to 3.4 V Select one: a. 0.501 ms b. 0.66 ms c. 0.44 ms d. 0.70 ms
Determine the equivalent inductance and equivalent current of the inductive circuit in Figure Q4. If L5 is replaced with a capacitor of 0.5 mF, how would it affect the branch current? The alternating Voltage source has an amplitude of 20 Vm. Vm Sine 50 Hz L1 5 mH L2 3 mH cele rele Figure Q4 rele celer L3 6.6 mH L4 2.8 mH reler L5 7 mH
A series R–L–C circuit comprises a 5µF capacitor, a 4ohm resistor and a variable inductance L. The supply voltage is 10∠0◦ V at a frequency of 159.1 Hz. The inductance is adjusted until the p.d. across the 4 ohm resistanceis a maximum. Determine for this condition (a) the value of inductance, (b) the p.d. across each component and (c) the Q-factor of the circuit.