Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 3.6 m, b = 1.2 m, w = 32 kN/m, P = 70 kN, and Mg = 61 kN-m. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Determine the maximum shear force and bending moment in the beam. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. P "| W MB a A b BO X

Use the graphical method to construct the shear-force and bending-moment diagrams for the beam shown. Let a = 3.6 m, b = 1.2 m, w = 32 kN/m, P = 70 kN, and Mg = 61 kN-m. Label all significant points on each diagram and identify the maximum moments (both positive and negative) along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Determine the maximum shear force and bending moment in the beam. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. P "| W MB a A b BO X

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the beam shown, the magnitude of the concentrated load is P = 23 kN, the magnitude of the couple is MB = 350 kN·m, and the beam lengths are a = 7.2 m and b = 21.6 m.(a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A.(b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment.Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. Part 1 Cut a cross-section through the beam at variable distance x, where 0 < x < a. Derive equations for the shear force V and…
Problem 1: The cantilever truss is loaded as shown. All loads are applied normal to the top chord. Use the following values: F = 32 kN as well as A = 2,000 mm? and E = 200,000 MPa for all members. Compute the vertical displacement at point A using Virtual Work Method. Round off your answer to 2 decimal places. F E F F 3 m F = (32 kN) B -2 m D -2 m 2 m
For the beam shown in the figure, draw the shear force and bending moment diagrams using slope-deflection method. A w = 4 kN/m 8 m B m +-2m- C
Consider the beam given in the figure. Given: X= 18 kN and Eis constant. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. w = 4 kN/m 21 6 m B hinge 3 m. C 1 6 m -3m- AD Draw the shear and moment curves for the beam given in the figure.
Considering the fully restrained beam shown in Figure 2 where E = 200 GPa and I = 2x10^9 mm^4 If P = 70 kN, M = 100 kNm, L = 12 m., and G = 40 degrees. Use either the virtual work method or the method of consistent deformation and state what you use with a complete solution. thank you. 1. Determine the maximum positive and negative shear that is acting on the beam. 2. Determine the maximum positive and negative moment that is acting on the beam 3. Determine the maximum deflection of the beam. 4. If the maximum deflection is limited to 10mm, determine the diameter of the circular beam required.
A part of slab is given in the figure. The slab is supported by secondary beams AB, CD and EF which are placed with a 50cm spacing. The secondary beams transfer the load they carry to the main beams.In the figure, AE and FB are the visible part of the main beams. Finally, main beams are supported by the columns at both ends. The slab is under uniformly distributed load q=4.5 kN/m2. The span length L is 3,5 m. Determine the dimendions of rectengular cross-sections of timber beams CD and the main beam which has a length of 4 m.
Learning Goal: A beam with length L = 2.9 m is supported by a pin joint at A and a cable attached at C as shown in (Figure 1). It is subjected to the distributed load with w₁ =1.7 kN/m and w₂ = 2.1 kN/m. The angle between the cable and the beam is 0 = 35°. Determine the normal force, shear force, and bending moment acting at point B, located x = 0.6 m to the left of the end of the beam. D Wi W2 C B L Begin by finding the support reactions for the beam using the free-body diagram shown in (Figure 2). What is the tension in the cable? Express your answer to three significant figures with appropriate units What is the horizontal reaction force at A? Assume the forces acts in the direction shown, and use an appropriate sign. Express your answer to three significant figures with appropriate units. What is the vertical reaction force at A? Express your answer to three significant figures with appropriate units. Now calculate the internal loading at point B using the free-body diagram of…
For the beam shown, the magnitude of the concentrated load is P = 12 kN, the magnitude of the couple is MB = 150 kN·m, and the beam lengths are a = 4.7 m and b = 14.1 m. (a) derive equations for the shear force V and the bending moment M for any location in the beam. Place the origin at point A. (b) use the derived functions to plot the shear-force and bending-moment diagrams for the beam. Use your diagrams to determine the magnitudes of the maximum shear force and the maximum bending moment. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number.
The cantilever beam shown in Figure A is subjected to load magnitudes of Pz = 3.0 kips and Py = 8.1 kips. The flanged cross section shown in Figure B has dimensions of bf = 7.1 in., tf = 0.55 in., d = 11.5 in., and t = 0.35 in. Using L = 70 in., determine: (a) the bending stress at point A. (b) the bending stress at point B. (c) the angle for the orientation of the neutral axis relative to the +z axis. Note that positive angles rotate clockwise from the+z axis. FIGURE A P₂ L B tw bf D FIGURE B
Please answer in complete solution and draw an fbd.Note: Please use the second picture as guide for the formulas. Thanks°
need asap tysm
For the beam and loading shown, (a) Use discontinuity functions to write the expression for w(x). Include the beam reactions in this expression. (b) Integrate w(x) twice to determine V(x) and M(x). (c) Use V(x) and M(x) to plot the shear-force and bending-moment diagrams. Let a = 3.0 m, b = 1 m, WA = 18 kN/m, and wg = 45 kN/m. Label all significant points on each diagram and identify the maximum shear force and bending moment along with their respective locations. Clearly differentiate straight-line and curved portions of the diagrams. Note that answers may be positive or negative. Here, "maximum" refers to the largest magnitude value, but you should enter your shear force and bending moment with the correct sign, using the sign convention presented in Section 7.2 of the textbook. If the magnitudes of the largest positive and largest negative values are the same, enter a positive number. WB "| WA X C a Answer: Vmax Mmax KN kN.m B b