Problem 1 Integration Method: For the given beam below, answer the questions. El = constant: 12 kN/m A 6 m (a) Determine the reactions at point B, RBy and MB. List 4 boundary conditions (Hint: 2 force boundary conditions and 2 geometric boundary conditions) (c) Determine the equations of elastic curve, y(x), using the given x-coordinate. Determine the slope at point A, 04. (d)

Problem 1 Integration Method: For the given beam below, answer the questions. El = constant: 12 kN/m A 6 m (a) Determine the reactions at point B, RBy and MB. List 4 boundary conditions (Hint: 2 force boundary conditions and 2 geometric boundary conditions) (c) Determine the equations of elastic curve, y(x), using the given x-coordinate. Determine the slope at point A, 04. (d)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The T-beam is subjected to a bending moment of M = 150 kip in. directed as shown. Determine the maximum bending stress in the beam and the orientation of the neutral axis. Make sure you check all possible points (corners) for max stress and/or state other reasoning for the point that you pick. Answer: [σmax = 3.33 ksi, β = -63.1°]
Derive the equation of the resonance frequency of the uniform cantilever beam shown below by using method of conservation of energy. [Solution tips: Umax, maximum strain energy is equal to max. kinetic energy of vibrating body.] j'm dx ( M(x)² T. U = max El xp- 1/2
Problem III. Solve the problem using Conjugate Beam Method. From the given fixed beam at both ends, solve the following questions using constant El. 12kN/m a. Reactions at A b. Reactions at B 4kN/m c. Slope at 6m from B in radians d. Displacement at 4m from A in mm 4m 6m
The beams described in the problems for Section 9.9 have constant flexural rigidity El. A simple beam AB of length L is loaded at the lefthand end by a couple of moment M, (see figure). Determine the angle of rotation 6, at support A. (Obtain the solution by determining the strain energy of the beam and then using Castigliano's theorem.) Mo B L PROB. 9.9-1 Step-by-step solution Step 1 of 5 A Length of the simple beam AB = L Couple of moment at A,= M, Angle of rotation at A= 0,
Use either the Virtual Work Method or the Method of Consistent Deformation. Please state what you use and please show the complete solution Considering the beam shown in Figure 1, E = 200 GPa and I = 2x10 ^9 mm^4 Determine the vertical reaction at support A. Determine the horizontal reaction at support A. Determine the Moment reaction at support A. Determine the vertical reaction at support C. Determine the vertical deflection of point B due to the loads Determine the horizontal deflection of point B due to the loads Determine the total deflection of point B due to the loads with respect to its original location.
For the beam and loading situation shown in the figure; (c) Find the elastic curve equation for the interval AB (y).(d) the displacement value at the midpoint of the interval AB (x = 3L)calculate.
Figure Q1 shows a statically determinate plane truss subjected to a verticalconcentrated load at C and E. The truss is made using steel with Modulus of Elasticity is210 GPa, and the cross section area for all members are 30 mm2. Assuming P is the 10 and a is half of P, determine the vertical displacement at F. Thesolution can be based on Method of Conservation Energy or Method of Virtual Work.
Figure Q2 shows a statically determinate plane truss subjected to a horizontal concentrated load at B. The truss is made using steel with Young's modulus of 205 GPa, and the cross section area for all members are constant. If the horizontal displacement at B is limited to 10 mm, determine the minimum cross section area required for the truss. The solution can be based on Method of Conservation Energy or Method of Virtual Work. (а) (b) Based on Q2(a), suggest an appropriate steel bar measurement.
A beam having a tee-shaped cross section is subjected to equal (12 kN.m) bending moments, as shown in Figure. The centroid location (y-) is (110 mm) measured upward from bottom edge of stem, the moment of inertia about the z axis, is (Iz 18646000 mm4).Determine the maximum bending stress produced in the cross section. State whether the normal stress is tension (T) or compression * .(C) 100 mm 25 mm 12 kN-m 175 mm 150 mm 12 kN-m 25 mm 70.8 MPa (T) O 75.8 MPа (С С 45.0 MPa (T) O 30.8 МPа (С) О
A rectangular beam is supported at both ends. It carries two concentrated load of 190KN, a clockwise moment of 160KN- m, and a uniformly distributed load "w". The modulus of elasticity of the beam is 150GPA. Solve the following if the reaction at point B is 309.63888888889KN, upward. USE ANY МЕТНOD BEAM DIMENSION: Width = 130mm , %3D Height = 460mm %3D NOTE: b = 4.2m ; Also, DON'T FORGET TO TYPE DOWN THE CORRECT UNITS (IF NEEDED) P W M 1m 1m 1m Determine the deflection at midspan
Figure Q2(a) shows a cantilever beam that is subjected to a pure bending moment M = 3kN.m about the neutral axis (N.A) and the cross-section of a beam is shown in Figure Q2(b). Determine: (a) The moment of inertia about the neutral axis, InA. (b) The bending stress acting at point B and state whether it is in tension or compression. (c) The bending stress acting at point C (d) The maximum bending stress in the beam. M Figure Q2 (a) 20 mm B 150 mm C N 20 mm 150 mm 20 mm 250 mm Figure Q2 (b)
Determine the following unknowns on the beam shown below using Conjugate-Beam Method. Consider 250 mm x 250 mm section and E = 200 GPa. Show complete and organized solution. a. Vertical Reaction at C in kN.b. Moment Reaction at C in kN-m.c. Deflection at point B in mm.d. Maximum deflection on the beam in m Valuea = 4.8b = 28c = 11 Thank you very much!