Answer the Question fast Two transformersA and B areconnected in parallel to a loadof (2+j1.5) ohm.Theirimpedances in Secondary termsZA = (0.15+j0.8) ohm and Zb =(0.1+j30.6)ohm Their no-loadtermind voltages areEA=200<0 V and EB=210<0Volt.Find the power and Powerfactor of each transformer?%3D%3D

It is given that: ZL=2+j1.5 ΩZA=0.15+j0.8ZB=0.1+j30.6EA=200 VEB=210 V

Answered: Two transformersA and B are connected…

Engineering

Electrical Engineering

Two transformersA and B are connected in parallel to a load of (2+j1.5) ohm.Their impodancon in anodan cos co ndarutorm

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

19. When you're connecting a bonding jumper to the structural steel of a building, the jumper must remainaccessible unless it'sA. located within five feet of the service equipment.B. covered in fireproofing material.C. behind a metal panel.D. inside a wall area
Briefly discuss the loaded and non-loaded telephone cables
Fill in the blanks: Q. Other name of CCD is _______________ Device.
hi.. question as per attached
Refer to the National Electrical Code® or the working drawings when necessary. Where applicable, responses should be written in complete sentences. For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is 12 ft x 18 ft (~3.7 m x ~5.5 m) with a 9 ft (2.8 m) floor-to-ceiling height. The spacing ratio for the luminaire is 1:0. 1. The maximum distance that the luminaires can be separated and achieve uniform illuminance is ft ( m). For problems 2-5, two luminaires, 8 ft (2.5 m) and 4 ft (1.2 m) in length with dimensions as shown in Figure 15-7, are to be installed in tandem (end to end). The end of the long luminaire is to be 2 ft (600 mm) from the wall. 2. The center of the outlet box should be roughed in at ft ( m) from the wall. 3. The first support should be installed at the wall. ft ( m) from 4. The second support should be installed at from the wall. ft ( m) 5. The final support should be installed at the wall. ft…
1. The only exception to the need for all information technology equipment to be satisfactorily grounded is where the equipment is A. DC powered.B. backup generator powered. C. double-insulated.D. isolated equipment. 2. Which section of the National Electrical Code lists sizing requirements for wire-type equipment grounding conductors? A. 250.66 B. 250.118 C. 250.4 D. 250.122 3. Which of the following statements about grounding electrical equipment is true?A. If no wire-type equipment grounding conductors are present with the branch circuits, the equipment grounding terminal bar isn't required.B. Grounding electrical equipment increases the possibility of metal parts remaining energized.C. The nonmetal parts of some electrical equipment are required to be connected to an equipment grounding conductor. D. Equipment grounding conductors can be spliced together outside of a grounded metal box. 4. Which of the following is a condition that must be met in order to qualify for the exemption…
Identify the given statement. The FCC has designated a 20-MHz range of frequencies ranging from 88 MHz to 107 MHz to the commercial FM broadcast service. Select your answer. The statement is a case-to-case basis. The statement is false. The statement is true. The statement has no fixed information.
How did you find the angles? Also my computer says the answer to (a.) is incorrect.
Topic Air Blast Circuit Breaker? Individual submission only accepted.  Minimum 350 words.  Reference should be added. .
Arduino - (b) The Arduino IDE provides a serial monitor for soft debugging purposes. Demonstrate how this can be accomplished by writing a simple program to perform the following task continuously on an Arduino UNO: Read a digital input from an external push button and print the state of the button as "Pressed" or "Not Pressed" to the serial monitor. The push button is connected to digital pin 5, and is configured as active low. Apply the proper Arduino C setup and loop structure, and present suitable comments with each line of your program.
1.7 Fill in the blanks with the words or phrases in the box: Separated , production, techniques ,has been , as well as, involve, delivered, growth , spread 1. Goods will be ... .once you make a request. 2. Human demands increase as.. .in population increases. 3. Because of high sales, car companies have extended their 4. Flame and fuel should be always..... to avoid fire. 5. High quality of production is necessary to gain profits.. .good reputation. ......... 6. World Wide Website .is a new technology of communication. 7. New plans of industry development . .further expenditure. 8. Different administrations management. ..... . can lead to successful
Whats oms law??