What components make up an ADT, exactly? Indicate your answer where indicated.

Q: 10e 2052 MAA IT SWI * )30V そ50 352 MAM 13 2

A: It is given that:

Q: Discuss the concept of block diagrams and how they are used to represent system models.

A: We have to discuss the concept of block diagram and how they are used to represent system model.

Q: Consider a 6-bit ADC and full scale voltage measurement range of (0-58).The Resolution  will be

A: ADC resolution

Q: ripple counter“

A: Counter- A device used for counting binary numbers is termed as digital binary counter. Digital…

Q: -In 8086 microprocessor, carry flag may be set by the instruction LEA. O CWD. SUB. NOT. -A name or…

A: The solution can be achieved as follows.

Q: Identify the type of signal as shown on the following figures. Also, indicate the equation defining…

A:

Q: The channel capacity is Select one: O a. all of the mentioned O b. information contained in a signal…

A: The channel limit, C, is characterized to be the greatest rate at which data can be sent through a…

Q: What happened to the led speed blinking when the delay was changed?

A: /* Blinking LEDs- Program to run that the LED is connected to pin 6 and the delay is one second…

Q: What are the major components of a SCADA system in a Nuclear Power Plant? Provide its functions.…

A: We need to tell about major components of a SCADA system in a Nuclear Power Plant? Provide its…

Q: 4. Build an AND gate using transistors, switches and LEDs. Pressing the switch should emulate…

A:

Q: Q.3 For Resistance temperature detectors (RTDS) I) What's the principle of operation for Resistance…

A:

Q: Chose the correct answer 7- When does over-modulation occur? a) Modulating signal voltage carrier…

A: This question is related to the modulation process.    When does over-modulation occur?…

Q: Enumerate and define the classification of electronic communication

A: Communication is the way of expressing the thoughts in the form of messages from one end to the…

Q: Answer it ASAP..

A: Two way multiplexer  It is defined as 2n×1 mux Here n=1 that means one selected line with this MUX…

Q: In the circuit given in the figure, calculate the IC current by full analysis, as R1 = 18.10Kohm, R2…

A: Here in the question there interested in the collector current.     To calculate the collector…

Q: What is counter? What is its purpose? Design an asynchronous counter that counts from 0 to 32 ?

A: In this question we will write about counter and it's purposes.. Note:- due to bartleby policy, I am…

Q: ____________ is the graphical technique in circuit analysis which de- scribes the output circuit,…

A: Transfer characteristics

Q: What is common channel signaling? And how does it work?

A: Common channel signalling  It is signalling in which a group of voice and data channels share a…

Q: 2) Design a F.A using AND, OR, and NOT gate.

A:

Q: A uniform quantizer, with average quantization power of 67.5 mW, is used in a PCM system. 1) What is…

A:

Q: Assume you're the manufacturer of an FM radio receiver device. Write a user manual for your product.…

A: A radio receiver is an electrical equipment that is also known as a receiver, a wireless, or simply…

Q: 1. Before the TRIAC is triggered on, the voltage across its ma in terminals is equal to the ___volta…

A:

Q: Differentiate MCB and RCD and Explains its purpose in an installation?

A: MCB is an electrical switch designed for automatically working to protect the electrical circuit…

Q: Ql) Fill in the blanks: 1- The acronym VHDL stands for, 2- FPGA consists of a matrix of…

A: fill in the blanks questions may have multiple answers The best suited answer need to be choosen…

Q: 1. Are the following statements correct or wrong? a) Thyristors are used only for low voltage, low…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: 1. Are the following statements correct or wrong? (a) Thyristors are used only for low voltage, low…

A: We are authorized to answer one question and three subparts at a time, since you have not mentioned…

Thermistors

A thermistor is a special type of resistor whose resistance is more temperature-dependent than standard resistors.  The resistance of the thermistor decreases with increasing temperature. This is the basic principle of thermistors. This allows the thermistor circuit to detect very small temperature changes that cannot be observed with the Resistance temperature detectors (RTDs) or the thermocouples. Since the resistance of a thermistor is temperature dependent, it can be connected to an electrical circuit to measure body temperature. This high sensitivity to temperature changes makes thermistors very useful for accurately controlling and calibrating temperature measurements. In general, resistance increases with increasing temperature in most metals, but thermistors react negatively.