Two previously undeformed cylindrical specimens of an alloy are to be strain hardened by reducing their cross-sectional areas (while maintaining their circular cross sections). For one specimen, the initial and deformed radii are 15?? and 12??, respectively. The second specimen, with an initial radius of 11??, must have the same deformed hardness as the first specimen. Compute the second specimen’s radius after deformation

Q: Example: the low cycle fatigue of a certain steel is given by life cycle equation-2: (of/E)=0.005…

A: The fatigue strength of steel /Modulus of elasticity(E), The fatigue Ductility coefficient is, The…

Q: Which of the following option does not match? Material Nature Stress-Strain Behaviour a) Elasto -…

A: Elastic: When stress increases with increase in strain is elastic zone of the material. Plastic:…

Q: A single crystal of a metal is oriented for a tensile test such that its slip plane normal makes an…

A: Given tensile stress = 1.3 MPa We are asked to compute the critical resolved shear stress for the…

Q: A metallic rod of diameter do is subjected to the tensile test. The engineering stress and the true…

A:

Q: Which of the following is the best representation of the samples' (A and B) axial strains when…

A:

Q: 400 200 Strain 0.05 0.10 0.15 0.20 From your graph, plotting the yield stress against 1/vd, you…

A:

Q: A 7075-T651 alloy is used in a structural component in an airplane. The component must not fail when…

A: Approach to solving the question:Identify the relevant information provided in the problem…

Q: An aluminum alloy [E = 67 GPa; v=0.33; a = 23.0 × 10-6/°C] plate is subjected to a tensile load P.…

A:

Q: B. C E Strain FIGURE Q1 (a) Stress -

A:

Q: A 2.0 m steel is being subjected into a tensile test. At force 30 kN, the length of the steel is now…

A: Given, Initial length of the steel subject (Li) = 2 m Length of steel after loading (LL) = 2.2 m…

Q: An aluminum specimen originally 300 mm long is pulled in tension with a stress of 275 MPa. If the…

A: Hooke's law: With in the elastic limit , Stress is always directly proportional to strain. when we…

Q: An aluminum tensile test specimen has a diameter, do = 25 mm and a gauge length of Lo = 250 mm. If a…

A: Given : do = 25 mm Lo = 250 mm  Force = 175 kN  Elongation of Gauge length = 1.25 mm  This is a…

Q: What are the Brinell and Rockwell hardness numbers for the brass specimen with its engineering…

A: For the brass specimen, the stress-strain behavior for which is shown in Figure 4b (i) , the…

Q: 8.30 Ifa component fabricated from an S-590 alloy (Figure 8.30) is to be exposed to a tensile stress…

A: The given tensile stress is 300 Mpa Temperature- 6500 C Estimate its rupture strength using the…

Q: A setup for single-edge-notch-bending (SENB) tests is shown below. Support rollers provide…

A: Given Data: Thickness of the specimen is t=10 mm. Height of the specimen is W=10 mm. Modulus of…

Q: A ceramic specimen having a circular cross section of radius 2.7mm is subjected to a load of 900N.…

A:

Q: The final temperature

A:

Q: A bar of length 5.0 m is made of a structural steel having the stress-strain diagram shown in the…

A: Given data,bar length = 5m=5000mmYield stress=250MpaModulus of elasticity=200Gpa=200 x 103…

Q: A steel 0.6 inch×1.2 inch steel 90 m long is subjected to a 45 KN tensile load along its lenght.If…

A: Given data, Width B = 0.6 inch = 15.24 mm Thickness D = 1.2 inch = 30.48 mm Length L = 90 m = 90000…

Q: A. Which material is considered as ductile and which one is considered as brittle? Explain. What is…

A: Part A) Material A has a typical ultimate stress point and breaking stress point, along with a clear…

Q: A cylindrical polymer with a diameter of 10nm when stress is applied to it and a change in diameter…

A: Let the applied Force be F in Newton and A is the area of polymer.Area of…

Q: 8.11 SizN4 has a surface energy equal to 30 J/m? and an atomic spacing ao = 0.2 nm. Calculate the…

A:

Q: A batch of casted mild steel has a modulus of elasticity of 200 GPa and a yield strength of 250 MPa.…

A: Calculate the modulus of resilience modulus of resilience=σ22Ehere σ is stress or yield strength, E…

Q: A tension test for a steel alloy results in the stress-strain diagram shown in Figure. Calculate the…

A: Consider the graph,

Q: In the figure shown below, determine: 1) The final temperature if the normal stress at aluminium is…

A:

Q: Question One (Compulsory) The following results were obtained during a tensile testing of a highiy…

A: Note:-  Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: A mild steel specimen originally 300 mm long is pulled in tension with a stress of 500 MPa. If the…

A:

Q: A tensile force of 5 kN produce an elastic reduction in diameter of 4 x 10-4 mm on a metal alloy…

A: given data: Force (F)=5 KNdiameter (d)=6 mmreduction in diameter(∆d)=4×10-4  mm

Q: A 2-ft rod with a modulus of elasticity of 8840 ksi, is subjected to a tensile force of 1000 lb and…

A:

Q: A square specimen of Magnesium Oxide is loaded in a 3-point bending test. If w = h = 6.2 mm is the…

A: Given Data: Load applied= 494 N h=w=6.2 mm Flexural strength= 117.1 MPa

Q: Determine the Basquin's law equation for the alloy. Use the following fatigue data, (about a…

A:

Q: For a material with poisons ratio 0.25, the ratio of modulus of rigidity to modulus of elasticity…

A: Given, Poisson's ratio, v = 0.25 Find, The ratio of modulus of rigidity to the modulus of elasticity…

Q: A tensile test was done on a steel specimen with the gauge length of 525 and a stress of 175 MPa. If…

A:

Q: A tensile force of 5 kN produce an elastic reduction in diameter of 4 x 10-4 mm on a metal alloy…

A:

Q: The assembly shown is composed of a steel shell and an aluminum core that has been welded to a rigid…

A:

Q: An engineer is laying out a design for a ceramic component whose volume is 30.3 mm. In the processes…

A: Weibull modulus = 9.5Characteristic strength = 628Volume of reference sample =5.3 mm3If the maximum…

Q: 90 alloy component as shown in following figure that is subjected to a stress of 200 MPa (29,000…

A: Given data stress= 200 MPa rupture lifetime be 509 h

Q: a.) Plot the S-N curve for this alloy. b.) Does this material have an endurance limit? Explain. c.)…

A: As per company policy, we are supposed to answer only the first three subparts. Kindly repost to get…

Q: The stress-strain tests were carried out on five different metals (A, B, C, D and E) and the results…

A: The following characteristic is seen from the stress-strain diagram given:

Q: Example: the low cycle fatigue of a certain steel is given by life cycle equation-2: (of/E)-0.005…

A: Solution: Given Data: Fatigue strength coefficientSfModulus of ElasticityE=0.005Fatigue strngth…