Two plates are connected by fillet welds of size 10 mm and subjected to tension, as shown in the figure. The thickness of each plate is 12 mm. The yield stress and the ultimate stress of steel under tension are 250 MPa and 410 MPa, respectively. The welding is done in the workshop (partial safety factor, ymw = 1.25). As per the Limit State Method of IS 800: 2007, what is the minimum length (in mm, rounded off to the nearest higher multiple of 5 mm) required of each weld to transmit a factored force P equal to 275 kN? 100 mm P P 150 mm

Two plates are connected by fillet welds of size 10 mm and subjected to tension, as shown in the figure. The thickness of each plate is 12 mm. The yield stress and the ultimate stress of steel under tension are 250 MPa and 410 MPa, respectively. The welding is done in the workshop (partial safety factor, ymw = 1.25). As per the Limit State Method of IS 800: 2007, what is the minimum length (in mm, rounded off to the nearest higher multiple of 5 mm) required of each weld to transmit a factored force P equal to 275 kN? 100 mm P P 150 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

i need the answer quickly
A combined section of steel and copper is subjected to a compressive load. Refer to the table below for the properties of each Steel Copper Area, A 900 mm2 1,200 mm2 Modulus of elasticity, E 200 GPa 120 GPa ents Allowable compressive stress 140 MPa 70 MPa ces ents Which of the following most nearly gives the load, in percent, carried by the copper? ssors Select the correct response ication 44.44% Niki 55.56% Blogs 66.67% 33.33% Courses
True of false? The more ductile steel is, the greater will be its toughness.
The 10-mm-diameter steel bolt is surrounded by a bronze sleeve. The outer diameter of this sleeve is 20 mm, and its inner diameter is 10 mm. If the yield stress for the steel is (ay) MPa, and for the bronze (ay)or 520 MPa, determine the magnitude of the largest elastic load P 640 that can be applied to the assembly. E 200 GPa, Ebr= 100 GPa. 10 mm 20 mm Figure 2: Steel Bolt
Which one of the following types of steel is used in the manufacturing of metro and monorails? A B Mild steel D Cast steel C Manganese steel Bessemer steel
I need the answer as soon as possible
What is the approximate value of the tensile strength governed by yielding of the cross- section of a roof truss diagonal 100 x 75 x 6 mm (fy = 250 MPa) connected to the gusset plate by 4 mm welds as shown in figure? (Take partial safety factor as 1.10) 1 H 100 4 mm weld, 140 mm long 75 A₂ = 1010 mm² Weld 310 mm long
#2 will upvote to anyone who will answer
What do you mean by Corrosion of Steel
If the modular ratio is equal to 7, and the Modulus of Elasticity of the Steel is 200,000 MPa. What is the value of fc'?
The assembly is composed of a steel shell and an aluminum core that has been welded to a rigid plate. The gap between the plate and the aluminum is initially 1- mm. If the assembly's temperature is reduced by 180°C, determine (a) the final axial stresses in each material and (b) the deflection of the rigid bar. To support your response, draw a deformation diagram with appropriate labels. Use the following properties: Aluminum core Steel shell Diameters (mm) d = 15 mm do = 30 mm d₁ = 20 mm E (GPa) 70 200 2 m a (/°C) 22 x 10-6 12 x 10-6
A thin cylinder 500 mm in diameter is made by providing a longitudinal lap joint with 8 mm shop fillet weld on two side as shown in figure. What will be the design pressure (in N/mm2) of fluid that can be allowed in the cylinder based on the strength of weld? Grade of steel used for load is Fe410. Weld