Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts connecting the two metal bars together and each bolt has diameter dbolt = 12.7 mm. The flange is oriented at angle = 55° with respect to longitudinal axis of the metal bars. If an axial force F = 40 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. SFoverall F 2.576 Ө x 0% F

Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts connecting the two metal bars together and each bolt has diameter dbolt = 12.7 mm. The flange is oriented at angle = 55° with respect to longitudinal axis of the metal bars. If an axial force F = 40 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. SFoverall F 2.576 Ө x 0% F

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The two steel shafts (1) and (2) each Ø10 should be connected to each other with the help of the sleeve (3) (Øinner = 10, Øoutside = 15) also made of steel and two rivets at the points shown. The shaft (1) is firmly clamped on the left- hand side, the force F = 100 N acts on shaft 2 in the direction of the arrow. How are the brass round rivets to be dimensioned so that a safety of the coupling against failure of S = 10 is achieved? hole for rivets 1 F 3 a) What type of connection does a riveted connection have? b) What type of load does the rivet have? c) What is the diameter of the rivets? d) Which areas of the rivet are loaded? (Draw in figure and formula) e) Dimension the rivet
Two metal bars are fastened together at the bolted flange connection shown. There are 4 total bolts connecting the two metal bars together and each bolt has diameter = 50° with dbolt 12.7 mm. The flange is oriented at angle respect to longitudinal axis of the metal bars. If an axial force F = 40 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. = F SFO overall = Ө number (rtol=0.01, atol=1e-05) F ?
Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts connecting the two metal bars together and each bolt has diameter dbolt 12.7 mm. The flange is oriented at angle = 50° with respect to longitudinal axis of the metal bars. If an axial force F = 30 kN is applied as shown, determine the overall safety factor of the bolted connection. You may assume the bolts are made out of 1020HR steel and the strength of the bolt in shear is 50% of the tensile strength of the bolt material. F - SF overall = 0 number (rtol=0.01, at F ?
Downvote for incorrect answer The connection is made using a bolt and nut and two washers. If the allowable bearing stress of the washers on the boards is (b)allow 2 ksi, and the allowable tensile stress within the bolt shank S is (allow 18 ksi, determine the maximum = allowable tension in the bolt shank. The bolt shank has a diameter of 0.31 in., and the washers have an outer diameter of 0.75 in. and inner diameter (hole) of 0.50 in.
The AB bond must be made of a steel for which the normal stress limit is 450 MPa. Determine the cross-sectional area for AB for the which the safety factor is 3.50. Suppose the link is adequately reinforced around the pins at A and B. What is the deformationof bar AB when subjected to the load applied to it considering the modulus of elasticity of steel E = 210 Gpa and the length L of thebar equal to 0.75m (All dimensions are in meters)?
Q1/ A bracket is supported by means of 4 rivets of the same size. Design the 7. Alalkau diameter of the rivet if Ou (tenşile ultimate stress) for the rivet material is 560MPA. Which of the rivet has max resistance? 20KN 20KN B0mm 30 mm 30 mm 30 mm
For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 68 kips. O 18.9 ksi O 30.8 ksi O 36.5 ksi O 33.1 ksi O 22.7 ksi
For the connection shown, determine the average shear stress in the 0.75-in.-diameter bolts if the load is P = 54 kips. P O 17.8 ksi O 14.8 ksi O 20.1 ksi O 24.4 ksi O 22.9 ksi
The one end of a hollow square bar whose side is 10.50 in with 1.50 in thickness is under a tensile stress and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σallowable=243 ksi for pin material.
A long tensile member is constructed by connecting two plates as shown. Each plate is 2 in x 9 in, A572 grade- 50 steel with an ultimate strength of 65 ksi. The fasteners are 2 in diameter bolts. Disregard the shear strength of the bolts, and disregard eccentricity. 2.75 in 0.5 in 2 in O O, 2.5 in 9 in 2.5 in FO o° 2 in G E The maximum tensile load the connection can support is most. nearly (A) 140 kips (B) 150 kips (C) 170 kips (D) 200 kips
The one end of a hollow square bar whose side is 10 in with 1 in thickness is under a tensile stress 102,500 psi and the other end is connected with a U bracket using a double-pin system. Find the minimum diameter of pin is used according to shear strength. Take the factor of safety as 1.5 and σ allowable= 243 ksi for pin material.
Please answer and provide a clear solution. thankyou. The five-bolt connection must support an applied load of P = 2600 lb. If the average shear stress in the bolts must be limited to 25 ksi, determine the minimum bolt diameter that may be used for this connection.