Three loads are connected in parallel across a 1400-V rms, 60-Hz single-phasesupply as shown in Figure 2.8.Load 1: Inductive load, 125 kVA at 0.28 power factor.Load 2: Capacitive load, 10 kW and 40 kvar.Load 3: Resistive load of 15 kW.1400 V(a) Find the total kW, kvar, kVA, and the supply power factor.112(b) A capacitor of negligible resistance is connected in parallel with the above loadsto improve the power factor to 0.8 lagging. Determine the kvar rating of this ca-pacitor and the capacitance in uF.133

Given circuit is,Asked to find,Total Active, reactive and apparent power, supply power…

Three loads are connected in parallel across a 1400-V rms, 60-Hz single-phase supply as shown in Figure 2.8. Load 1: Inductive load, 125 kVA at 0.28 power factor. Load 2: Capacitive load, 10 kW and 40 kvar. Load 3: Resistive load of 15 kW. (a) Find the total kw, kvar, kVA, and the supply power factor. 1400 V 14 1 12 2 (b) A capacitor of negligible resistance is connected in parallel with the above loads to improve the power factor to 0.8 lagging. Determine the kvar rating of this ca- pacitor and the capacitance in uF. 3 13

Three loads are connected in parallel across a 1400-V rms, 60-Hz single-phase supply as shown in Figure 2.8. Load 1: Inductive load, 125 kVA at 0.28 power factor. Load 2: Capacitive load, 10 kW and 40 kvar. Load 3: Resistive load of 15 kW. (a) Find the total kw, kvar, kVA, and the supply power factor. 1400 V 14 1 12 2 (b) A capacitor of negligible resistance is connected in parallel with the above loads to improve the power factor to 0.8 lagging. Determine the kvar rating of this ca- pacitor and the capacitance in uF. 3 13

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7MCQ

See similar textbooks

Similar questions

What is the average Power at maximum resistance? Why? What is the effect to the voltage and current when increasing the load resistance?
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
60. An RLC series circuit connected to a 110-volt and 50-cycle AC source, contains the following series resistances and reactances: R1=10 ohm, R2= 15, XL1=20 ohms, XL2=25 ohms, XC= 40 ohms. Find the real power. a. 65.3899 b. 392.4372 c. 397.848 d. 588.6559
Need asap pls help. Solve for the voltages across and currents through each component. Show the complete solution and explain. The total power should be zero..
The section bus-bars A and B are linked by a bus-bar reactor rated at 6000 kVA with 12% reactance. On bus-bar-A, there are two generators each of 10 MVA with 8% reactance and on bus-bar-B, two generators each of 6000 kVA with 10% reactance. Find the steady MVA fed into a dead short circuit all phases on B with bus-bar reactor in the circuit.
The temperature of a noninductive heater unit is controlled by a reactor. The heater unit and the reactor are connected in series across a 250 V, 60 Hz source. The voltage across the heater unit is 200 V. The voltage across the reactor is 100 V. The current in the circuit is 10 A. Determine: the power factor of the series circuit. the power factor of the reactor. the impedance of the reactor. the effective resistance of the reactor. the inductive reactance of the reactor
For the single-phase circuit shown in Figure 2.22, I5 10/08A. (a) Compute the phasors I1, I2, and V. (b) Draw a phasor diagram showing I, I1 I2, and V
(b) A symmetrical three-wire three-phase supply as shown in Figure Q2(b) is connected to a balanced three-phase load. The value of impedance, Z is identified to be 100-j75 Q. (i) Find IaB, IBC and ICa (ii) Determine Iaa, IbB and Ic (iii) Determine Iba, Isb and Ix (iv) Draw the phasor diagram of all currents in Q(b)(i) and Q(b)(ii)
In the system shown in Figure 1, the transformers are connected star-star with both star points grounded and the generators are connected in star with thier star points grounded. The system base is 15 MVA. The transformers all have reactances of 0.04 p.u. on this 15 MVA base. The reactances of all other elements are given in Table 1 (in 2) and the voltage levels are given in Table 2. p.u. G1 p.u. T1 jö Per-Unit Convert all values to p.u. on a 15 MVA base. Xa= p.u. Xc₂= XL = V BABE G1 2 X 9 T3 Figure 1: A section of the distribution system T1 L Table 1: Sequence reactances (2) 3 G1 L G2 0.3 0.59 0.01 4 L 9/10 10 Fault Voltage What is the voltage at bus 3 (in Volts) after the fault has occurred? Vp= V T2 5 T2 34 10/4 Table 2: Voltage bases (kV) G2 4 T3 10/9 | G2 Fault Current A three-phase fault with a fault reactance of 0.01 p.u. occurs at bus 3. Calculate the fault current flowing at the fault point in KA. Ip=-j KA So
Q20. The section bus-bars A and B as shown in Figure B5 are linked by a bus-bar reactors each rated at 5000 kVA with 10% reactance. On bus-bar A, there are two generators each of 10,000 kVA with 10% reactance and on B two generators each of 8000 kVA with 12 % reactance. Find the Current and MVA that fed into a dead short circuit between all phases on B with bus-bar reactor in the circuit. Page 4 of 5 جامعة التقنية والعلومر التطبيقية بإبراء University of Technology and Applied Sciences - Ibra Student ID: Section: Student Name: 8,000 kVA 12% 10,000 kVA 10,000 kVA 10% 8,000 kVA 12% 10% 2 3 5,000 kVA 10% lell 8,000 kVA 10% Figure B5 "End of Question Paper"
Determine the rms current I as shown in figure 2. Source voltage is already in RMS value(Answer must be in polar formand should be in 4 decimal places).
(b) Differentiate between single phase and three phase alternating current (A.C) supply for the following aspects with adequate comparisons and sketches: (i) Generation of single phase and three phase e.m.f.s (ii) Sine waveforms(iii) Advantages or disadvantages of both phases