The working gas of a thermodynamic cycle is a diatomic gas (assume constant specific heats.) The gas originallystarts at 100kPa, 4m ³ and 27° C. It undergoes a four-step process ---• Process A-B: The gas is compressed at constant temperature to one-quarter of its original volume.• Process B-C: The volume of the gas is then doubled at constant pressure.• Process C-D: The gas then undergoes an adiabatic expansion.• Process D-A: The gas then undergoes a constant volume process back to its original statea) Make a table of the temperature, pressure, volume, internal energy, enthalpy, entropy and quality factor (T,P, V, U, H & S) at the start of each process.b) Make a table of the change in internal energy, heat flow, work done, change in enthalpy, and change inentropy (AU, Q, W, AH & AS) during each leg of the cycle.c) Draw well-labelled P-V & T-S diagrams (indicating lines of constant temperature, heat flow, work, etc.)d) Calculate the thermal efficiency of the cycle.

The objective of the question is to analyze a thermodynamic cycle involving a diatomic gas…

Answered: The working gas of a thermodynamic…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. In a cycle, a 4kg ideal gas (MW=3g/mol and k=2.3) confined in a controlled mass system went through three processes. The gas was started at 20kPa and 310K in the first process, and it was isometrically increased by 30kPa. The gas was subjected to 40OK using a process defined by PV^3=C. It returns to its original state polytropically. Calculate the entropy change for each process.
One mole of an ideal monatomic gas, occupying 5 L at 3270 °C, is carried through a Carnot cycle. It is first expanded isothermally to a volume of 25 L and then adiabatically to a stage at which the temperature is 270 °C. It is then compressed isothermally to a certain volume and then finally back to the initial state. Calculate the quantities of AE, q and W in each step. Then calculate the efficiency.
The working gas of a thermodynamic cycle is a diatomic gas (assume constant specific heats.) The gas originally starts at 100kPa, 3m3 and 27o C. It undergoes a four-step process --- • Process A-B: The gas is compressed at constant temperature to one-third of its original volume. • Process B-C: The volume of the gas is then doubled at constant pressure. • Process C-D: The gas then undergoes an adiabatic expansion. • Process D-A: The gas then undergoes a constant volume process back to its original state a) Make a table of the temperature, pressure, volume, internal energy, enthalpy, entropy and quality factor (T, P, V, U, H, S & x) at the start of each process. b) Make a table of the change in internal energy, heat flow, work done, change in enthalpy, and change in entropy (U, Q, W, H, S) during each leg of the cycle. c) Draw a welllabelled P-v diagram (indicating lines of constant temperature.) d) Calculate the thermal efficiency of the cycle
In a cycle, a 4kg ideal gas(MW=3g/mol and k=2.3) confined in a controlled mass system went through three processes.the gas was started at 20kPa and 310K in the first process, and it was isometrically increased by 30kPa. The gas subject to 400Kusing a process defined by PV^3=C.It returns to its original state polytropically.Calculate the entropy change for each process.
One mol of an ideal gas is taken through The gas is subjected a three-step cyclic process. successively to an isothermal expansion at 600 K from 5 to 3 bar (path a to b), a constant-pressure cooling (b to c), and a constant-volume heating (c to a). All processes are reversible. Cy and Cp AH for each step and for the entire process. Draw the cycle on the PV diagram. Compile all results in a table, as follows: 21.686 J mol-K-1 =30 J mol-1K-1. Calculate Q, W, AU and %3D
Required information Problem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. During the isothermal heat addition process of a Carnot cycle, 700 kJ of heat is added to the working fluid from a source at 400°C. Problem 07.021.c - Total entropy change for the process Determine the total entropy change for the process. The total entropy change for the process is KJ/K.
Problem 4: An engine operating on an ideal Diesel cycle has a cylinder volume when the piston is at bottom-dead-center (BDC), V₁ 1 liter = 0.001 m³. The intake pressure and temperature are P₁ = 300 K. The engine cycle contains the following processes: 100 kPa and T₁ = Adiabatic compression to V₁/24. Constant pressure heating to V₁/14. =
A good oil well in the Persian Gulf produces about 100,000 bbl of oil per day. What mass flow rate of steam from a geothermal well located at the Larderello field in north- ern Italy would be required to provide the same rate of energy production? Are there any practical limitations to achieving this production rate? The Larderello field produces saturated steam at about 20 bar, 212.4°C. Assume a typical Larderello well is about 28 cm in diameter and is about 2,500 m deep. The enthalpy of vaporization is 1,890.7 kJ/kg at 20 bar. Assume an average liquid phase heat capacity for water of 4,100 J/kg K. Note that the energy content of a bbl of oil, which is about 5 million Btu, is referenced to its heat of combustion at 25°C.
I just need help with parts (f), (g), (h) and (i) Problem 6: A certain gasoline engine is modeled as a monatomic ideal gas undergoing an Otto cycle, represented by the p-V diagram shown in the figure. The initial pressure, volume, and temperature are p1 = 0.95 × 105 Pa, V1 = 0.025 m3, and T1 = 310 K, respectively. Part (a) Calculate the number of moles times the gas constant, nR, in joules per kelvin, to three significant figures, using the ideal-gas law and the initial values of pressure, volume, and temperature. This quantity will be useful for later calculations. nR = 7.7 Part (b) The first step in the Otto cycle is adiabatic compression. Enter an expression for the work performed on the gas during the first step, in terms of V1, V2, and p1. W1→2 = p1 V1 ( ( V1/V2 )( 2/3 ) - 1 )/( 2/3 ) Part (c) Calculate the work performed on the gas during the first step, in joules, for V2 = V1/6.2. W1→2 = 8460.58 Part (d) Calculate the temperature of the gas, in…
3. The three-process cycle involves the following: polytropic compression from 1 to 2 where P=(145 +X) kPa, T=(87 +X) °C, constant-pressure cooling from 1-2 where P=(750+X) kPa; constant temperature heating from 3 to 1. If n=1.3, determine the: C. V1 d. T2 ANSWER ANSWER е. Р3 f. V3 ANSWER ANSWER 9. ТЗ h. Network ANSWER ANSWER i. Нeat ANSWER
Required information Problem 07.021 - DEPENDENT MULTI-PART PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. During the isothermal heat addition process of a Carnot cycle, 700 kJ of heat is added to the working fluid from a source at 400°C. Problem 07.021.b - Entropy change of source in a heat addition process Determine the entropy change of the source. (You must provide an answer before moving on to the next part.) The entropy change of the source is KJ/K.
In a heat engine, 2.60 mol of a monatomic ideal gas, initially at 4.00 atm of pressure, undergoes an isothermal expansion, increasing its volume by a factor of 9.50 at a constant temperature of 652.0 K. The gas is then compressed at a constant pressure to its original volume. Finally, the pressure is increased at constant volume back to the original pressure. What is the heat flow into or out of the gas during process 3? in kJ

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS