The two loads shown below can be described as follows: load 1 absorbs an average power of 60kW and delivers 70KVAR magnetizing reactive power; load 2 has an impedance of 24 + 7j. The voltage at the terminals of the loads is 2500 cos(120pi t) V. a. Find the rms value of the source voltage. b. Determine the total complex power of the source. c. What is the power factor of the source.

The two loads shown below can be described as follows: load 1 absorbs an average power of 60kW and delivers 70KVAR magnetizing reactive power; load 2 has an impedance of 24 + 7j. The voltage at the terminals of the loads is 2500 cos(120pi t) V. a. Find the rms value of the source voltage. b. Determine the total complex power of the source. c. What is the power factor of the source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The instantaneous voltage across a circuit element is v(t)=400sin(t+30)volts, and the instantaneous current entering the positive terminal of the circuit element is i(t)=100cos(t+10)A. For both the current and voltage, determine (a) the maximum value, (b) the rms value, and (C) the phasor expression, using cos(t) as the reference.
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
Lance Smile operated two loads in parallel. The loads draw a total of 3kW at a 90% power factor lagging operating at a 230 Vrms 60-hz voltage source. Load 1 is taking 1000 W at 80% power factor lagging. Determine the following: a. The power factor of the second load. b. If a capacitor is connected in parallel with the loads, what is the value of the capacitance needed to correct the power factor to 95% lagging for the combined load.
When a load is connected to a power line with a frequency of 230V (rms) 50 Hz, it draws 4500 W at a power factor of 0.80. Find the required capacitance value to increase the power factor to 0.85.
For the system in the figure: Find the total average power, total reactive power, total apparent power, and total power factor. Find the current Is (in phasor form). If the loads can be modeled as a resistance in series with a reactive element (capacitor or inductor), find the impedance of each load. Confirm the result of part B using the input voltage and the result of part C. ..
A 480-V rms source supplies a load that absorbs 100 kW at a 0.7 lagging power factor. A capacitor is then connected in parallel to this load to correct the overall power factor to 0.9 lagging. What reactive power must this capacitor produce to correct the power factor? What will be the resulting rms source current after connecting this capacitor?
The single phase AC sinusoidal voltage then the rms value of the voltage v is .........
A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.
Suppose I have two peak phasor voltages, V, = 100245° and V, = 75Z-60°. Circle Your Choices: I. The frequencies associated with the phasors are (0 Hz, 60 Hz, 50 Hz, Unknown). II. The rms value of the first phasor is (100, 70.7, 141, 200) volts. III. If you want to add these two phasors, the frequencies must be (60 Hz, 50 Hz, The same, Integer multiples of a given frequency.)
When a load is connected to a power line with a frequency of 230V (rms) 50 Hz, it draws 4250 W of power at a power factor of 0.85. Find the required capacitance value to increase the power factor to 0.95.
Calculate the capacitance that when placed in parallel with the load, will raise the power factor to unity. Please answer in typing format please ASAP for the like Please