The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 850 N, Q = 1050 N, LAB = 650 mm, Lgc = 1050 mm, Lcd = 1050 mm. A B C D P Answer: (a) VA = (b) vc= LAB LBC mm mm Q LCD

The solid 34 mm diameter steel [E = 200 GPa] shaft supports two belt pulleys. Assume that the bearing at B can be idealized as a roller support and that the bearing at D can be idealized as a pin support. For the loading shown, determine: (a) the shaft deflection at pulley A. (b) the shaft deflection at pulley C. Assume P = 850 N, Q = 1050 N, LAB = 650 mm, Lgc = 1050 mm, Lcd = 1050 mm. A B C D P Answer: (a) VA = (b) vc= LAB LBC mm mm Q LCD

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The circular steel shaft is subjected to two torques as shown. The segment AB is hollow, with outside diameter of 1 inch and an inside diameter of ½ inch. The segment BC is solid, with a diameter of 1 inch. Determine (a) the maximum shear stress in the shaft, and (b) the angle of twist in degrees between A and C, using G = 12 x 10⁰ psi. 750-in. Ⓡ 2 ft 2000-in. 18 Itin. 3 ft Lin.
The triangular plate shown with uniform thickness has a mass M = 129 kg. Use x = 1 m and y = 1.5 m. A load P = 529 N is also applied at position indicated. Determine the tension (in Newtons) developed in cables A, B, and C.
A simple torsion-bar spring is shown. The shear stress in the steel [G= 11,500 ksi] shaft is not to exceed 8800 psi, and the vertical deflection of joint D is not to exceed 0.400 in. when a load of P = 3000 lb is applied. Neglect the bending of the shaft and assume that the bearing at C allows the shaft to rotate freely. Determine the minimum diameter required for the shaft. Use dimensions of a = 70 in., b = 24 in., and c = 24 in. a b Answer: d= D P B in. C
Read the question carefully and give me right solution with clear calculations
answer only letters D and E
Detailed Solution please
The five 20mm-diameter rivets fasten the plate as shown in the figure to the fixed member. a). Determine the value of the load P so that the average stress of any rivet does not exceed 80MPa.b). What additional clockwise torque can be applied before the shearing stress exceeds 90MPa
Find the maximum moment of the given load train at point n on the beam given in the figure? (Single load and distributed load train move on the beam. (a=9 m between n-A, b=3 m between n-B)
2. The lap joint is fastened with four 30-mm-diameter rivets. The working stresses are 84 MPa for the rivets in shear and 84 MPa for the plates in bearing. Find the maximum safe axial load P that can be applied to the joint. Assume that the load is equally distributed among the rivets... 35 mm KATIN 160 mm
Ql:- The system of gears B and C take out power 150 and 175 hp respectively from a motor A that has 325hp, Find the shaft dimeter if the allowable shear stress is 6250 psi and the angle of twist between gear C and motor is 2 degree. Let G=11.5 x 10° psi. Gear Gear Motor A B
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. A 4 in. 3.5 in. 3.5 in. ID В C te-4 ft- | 2 ft - 6 ft-
stion 27 1 points Save Answe A built up l-section is formed from plates welded together as shown in the figure. It is to be used as a column L = 3.5 m long. All elements are A36 steel and connected such the section is fully effective. Using the following properties, calculate the flexural buckling stress, Fer, in MPa using theoretical k. Flanges: b = 150 mm, t = 17 mm Web: h= 310 mm, tw - 7 mm Write your final answer in two decimal places only. I L tw