Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt circle 320 mm in dia- meter and six 15-mm diameter bolts on a concentric bolt circle 240 mm in diameter. Determine the unit stress in each bolt due to a torque of 25 kN.m.

Q2 A flanged bolt coupling joins two shafts. It consists of eight 22-mm diameter bolts on a bolt circle 320 mm in dia- meter and six 15-mm diameter bolts on a concentric bolt circle 240 mm in diameter. Determine the unit stress in each bolt due to a torque of 25 kN.m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Given: Consider the W24 x 94 beam below with lateral support of the compression flange only provided…

A: Given

Q: A body of dimensions 1.5 m x 1.0 mx 2 m, weighs 1962 N in water. What is the weight of the body in…

Q: 2.Find the surface tension in N/m in a soap bubble of 30 mm diameter when the inside pressure is…

Q: e rectangular channel such that after it falls to the lowe- (P), V V V V V VR Yw2g' 29' 29' 29' 29'…

Q: P.1. The distributed load has a magnitude of w = 225 N/m. Determine the reactions at the roller at A…

Q: Three boards, each 2 in. thick, are nailed together to form a beam that is subjected to a vertical…

A: Given : Thickness of boards = 2 in. Allowable shearing force = 250 lb To Determine : Determine the…

Q: Nitrate is being leaked from an industrial facility with the concentration of 22 mg/L. If the…

A: Given, Co = 22 mg/L D = 1.95 x 10-7 m2/s τ = 0.35 V = 4.74 x 10-7 m/s t = 20 years = 6. 3 x 108 sec

Q: Given the tangent distance equal to 148.96 meters and the angle of intersection equal to 40, what is…

A: Given data in question Intersection angle 40 Tangent length 148.96 m To find out EXternal distance…

Q: Write the V and M equation of the beams loaded as shown and the diagram. Then repeat the method…

Q: A rigid bar is suspended by three rods made of the same material as shown in the figure. The area…

Q: 9. The soil under a dam has three layers with different coefficient of permeability. 3m 4m 6m K₁1.0…

Q: Problem 1 For the beam and loading shown, (a) draw the shear and bending-moment diagrams, (b)…

Q: B During a traffic speed survey, the following observations were recorded when a vehicle passes a 50…

Q: 3- The given solid block is subjected to the shown forces. Determine the normal stress at point A,…

A: A) Problem of Solid mechanics where we need to Determine the normal stress at point A and at point…

Q: = A proposed building is to be supported on a series of spread footing embedded 36 inches into the…

A: d= 36 inch Cc1+e0=0.12Cr1+e0=0.03s'm= 5000 lb/ft2g=120 lb/ft3GWT= 15 ft below the ground surfaceS=1…

Q: Q2. A 40 mm diameter jet has a velocity of 25 m/s. Calculate the resultant force on a large flat…

Q: 2 m -2m -3 kN -2m Determine the force in each member of the truss shown in the figure. Indicate…

A: Given Data Find the forces in each member.

Q: Problem 3/Question 6: You are inspecting the construction of a steel bridge. It is the cold- est day…

A: The given data is shown below: Length of rod=15mα=11×10-6°C-1

Q: Draw shear force diagram and bending moment diagram

A: Given data Draw shear force and bending moment diagram.

Q: Given: Consider the floor frame below supports a 6-in. concrete floor. Assume the beams and girders…

Q: LOKN 15KN 3M 3m 20KN Jm ISKN 3m Find the moment at A B 13 12 26KN

Q: Rigid member ABCD shown here is used to support a 2 kN weight. This member is 6-m-long. Steel (E =…

Q: In order to determine the elevation of top Q of a signal on a hill, observations were made from two…

Q: If staff readings taken on B and C by a tacheometer placed at A are Staff Distance (m) Stadia…

Q: For the girder in the figure, draw the influence lines for the reaction at I, the shear to the right…

Q: Describe your recommended medium for connecting between buildings if it is known that the distance…

A: Given data- Two buildings, Distance between buildings D=500 m, To Find- The medium for connecting…

Q: Q1. Find the horizontal thrust of the water on each foot of width of the sluice gate, given y₁ = 7…

Q: Please provide me with a well written PAGE long of a CONSTRUCTION TECHNIQUE to create solar panels…

A: Constructing a Solar Panel and Wind Turbine System as a Complete One Unit System Solar panels and…

Q: Example: For the three hinged arch shown in figure below, find the support reactions and axial force…

Q: 1. Determine the force in each member of the truss shown In Figure 1. Use method of Joints. State…

Q: Rigid member ABCD shown here is used to support a 2 kN weight. This member is 6-m-long. Steel (E =…

A: Given : E = 200 GPa Weight supported = 2 kN diameter = 0.5 cm length = 6 m To Find : Deflection of…

Q: 3. By using the left side of the figure. determine the force in members FH, FG, and EG by using…

A: A truss is given with roller support at A and hinged support at K Degree of static indeterminacy, Ds…

Q: The jib crane is designed for a maximum capacity of 15 kN, and its uniform I-beam has a mass of 220…

Q: A highway embankment with the geometry shown below is constructed from materials with the average…

A: A symmetrical trapezoidal highway embankment is given The top width of 10 m The side slope is 2 H:1…

Q: diameter and 10 m deep is placed in purely cohesive soil. If the cohesion the soil is 4t/m² and…

A: Capacity of Pile = End Bearing + Skin Friction Diameter of pile = 0.5m Length of pile = 10 m…

Q: Determine for the slope at support C and B, and deflection at every 0.5m interval. Take E =…

A: Lets Use MACAULAY'S Method for determining the Slope at Support B,C and Deflection at every 0.5 m…

Q: using method of sections. Determine the forces in members BC, BG, and FG.

Q: A cantilever beam, 4m long, carries a uniformly distributed load our total length. If the slope at…

Q: A concrete beam prestressed with a parabolic tendon is shown in the sketch. The eccentricity of the…

A: Given- Applied prestressing force at service = 1620 kN. Uniformly distributed load UDL= 45 kN/m…

Q: The outflow channel shown in Figure 10.10 is about 10 km across and 100 m deep. If it carried 107…

Q: A liquid compressed in a cylinder has a volume of 1000 cm³ at 2MN/m² and a volume of 993 cm³3 at 3.3…

A: Given- Volume V=1000 cm3 @ 2MN/m2, Volume V=993 cm3 @ 3.3 MN/m2,

Q: The following data were obtained by conducting liquid limit and plastic li tests on a soil collected…

A: To determine: a) Draw the flow curve and determine the liquid limit b) Using the Casagrande…

Q: A leaf spring of semi-elliptical type has 11 plates each 9 cm wide and 1.5 cm thick. The length of…

Q: a) With the context of town planning describe the importance of: 1. Natural resources 2. Economic…

A: Natural resources are substances that occur naturally and are valued in their largely unaltered…

Q: 2. Determine the horizontal and vertical components of reaction at the hinge A and the horizontal…

A: Hydrostatic forces on a curved surface comprises of both horizontal and vertical forces. The…

Q: Why do we occasionally need to reduce project duration? And how?

A: Project Duration: Project duration is the time mentioned for the completion of the project. Project…

Q: If the radius of a circular curve is 252.27 meters and one full station is 50 meters, what is its…

Q: The

Q: The monthly mean temperature of maximum daily temperature and monthly mean of average daily…

A: Given data: The monthly mean temperature of maximum daily temperature = Tm=40 °C The monthly mean…

Q: Explain why indoor air pollution levels can be much higher than ambient levels.

A: Air Pollution: The contamination of air due to atmospheric pollutants or any other pollutants in the…

Concept explainers

Types and properties of steel

Steel is an alloy of iron. It is formed by heating iron and combining carbon (0.1-1.7%) with it and minor amounts of other elements such sulfur, chromium, manganese, nickel, etc. Thousands of steel grades have been published, registered, or regulated around the world, each with its chemical composition, and special numbering systems have been devised in various countries to classify the vast number of alloys.

Question

Q2 A flanged bolt coupling joins two shafts. It consists
of eight 22-mm diameter bolts on a bolt circle 320 mm in dia-
meter and six 15-mm diameter bolts on a concentric bolt circle
240 mm in diameter. Determine the unit stress in each bolt
due to a torque of 25 kN.m.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A flanged bolt coupling consist of six 10 mm. diameter steel bolts on a bolt circle 300 mm. in diameter, and four 10 mm. steel bolts on a bolt concentric bolt circle of 200 mm. in diameter. (a) Determine the torque applied (N-m) if the shearing stress is 60MPa in the bolts. (b) If the torque capacity increased to 8 kN-m, determine the number of bolts of 10 mm. diameter on the 300 mm. bolt circle of the coupling.
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
2. The crank mechanism shown below is in equilibrium. Determine: a) the diameter of cylindrical connecting rod CD, given that normal stress is limited to 120MPa; b) the shear stress in the pin at B, where the pin has diameter of 8mm; and c) the bearing stress in the bracket supports at B. C 120° A 8kN 300mm B 30⁰ D P 200mm 6mm B 15mm 6mm 8mm Detail of pin and pin brackets
the connection consists of a plate connected to another plate by five 25-mm diameter rivets. it carries a load P = 80 kN. Determine the shear stress on the bolt due to the effect of force alone.
• 4. A flanged bolt coupling consists of eight steel 20-mm voits spaceu evenly around a bolt circle of300mm in diameter. Determine the torque capacity of the coupling it the allowable shearing stress in the bolts is 40MPa. Det the 4 ways to increace M3 HW 3 the torque capacity to 24 KN-m a) no. d bolts ) Ss d bolt: c) Dia of bolts Make sure that only one aspect i d) Dia of belt eircle) change vnad change vn ad
A flange bolt coupling consist of 8-12.7mm steel bolts on a circle diameter of 304.80mm & 6-12.7mm steel bolts on a circle diameter of 228.60 mm. is subjected to a 950KN-mm torque.The shear stress developed in the outer circle of the flange bolt coupling is ___ MPa. (A) 1.50 B 6.80 (C) 3.20 (D) 4.30 E 8.10
QUESTION 2 a) A solid alloy shaft 5cm diameter is to be coupled in series with a hollow steel shaft of the same external diameter. Find the internal diameter of the steel shaft if the angle of twist per unit length is to be 75% of that of the alloy shaft. Determine the speed at which the shafts are to be driven to transmit 200kW, if the limits of shearing stress are to be 55N/mm2 and 75N/mm² in alloy and steel respectively. Gsteel = 2.2Galloy b) A simply supported beam of span 20m carries two concentrated loads 4kN at 8m and 10kN at 12m from one end as shown in Fig. 2. Calculate (a)the deflection under each load, (b) the maximum deflection, E = 200 000 N/mm2; I= 10° mmª 4KN 10KN 8m 4m Y 20m
10/... find the shear stress in bolts 5 1) 80 kN 80 kN 8-bolt DIA. 10 MM 80 kN 80 kN 8-bolt DIA. 10 MM 110 MPa. 127 MPa. 509 MPa no one O 300 mm 8 mm
A flanged bolt coupling consists of 10-14-mm-diameter steel bolts on a bolt circle 500 mm in diameter, and 6-14-mm-diameter steel bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 73 MPa in the bolts? Answer must be in kN-m.
The solid spindle AB has a diameter d,=38mm and is made of a steel with an allowable shearing stress of 84 MPa, while sleeve CD (hollow cylinder with an outer diameter of 75mm and a thickness of 6mm) is made of a brass with an allowable shearing stress of 50 MPa. Determine the largest torque T that can be applied at A. 100 inm 200 min 1-6 ma B 75 man
4. A flanged bolt coupling consists of eight steel 20-mm voIs spaceu evenly around a bolt circle of300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress in the bolts is 40MP.. Det the 4 ways to increare M3 HW 3 the torque capacity to 24 KN-m a) no. d bofts ) Ss d bolti c) Dia of bolts d) Dia of belt eircle) change vn ad Make sure that orly one aspect a
Determine the a) normal stress in rod (1), b) the shear stress in pin B and the shear stress in pin A given the following properties of the structure. The tie rod at 1 is 10 mm in diameter. Pin Pin Connection Diameter SET e a b h Connection Type at B & D of pins Type at A A 1300 N 45° 600 250 450 Double Single Shear 12 mm mm mm mm shear D (1) C b