The soil element with known stress conditions is shown in following figure. (i) construct Mohr's circle for the soil element and determine (ii) stress condition of the plane AC (use double angel method); (iii) major and minor principal stresses; (iv) the angle between major principal plane and the plane "AD"; (v) maximum shear stress. Provide your answer up to one decimal point. [use graph paper to draw Mohr's circl 2 kN/m² + 7 kN/m² + 35° B 3 kN/m² 2 kN/m²

The soil element with known stress conditions is shown in following figure. (i) construct Mohr's circle for the soil element and determine (ii) stress condition of the plane AC (use double angel method); (iii) major and minor principal stresses; (iv) the angle between major principal plane and the plane "AD"; (v) maximum shear stress. Provide your answer up to one decimal point. [use graph paper to draw Mohr's circl 2 kN/m² + 7 kN/m² + 35° B 3 kN/m² 2 kN/m²

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.2P

See similar textbooks

Similar questions

Another way of testing flexure strength is by quarter point loading as shown. The sample section is 150mm x 150mm. If both P = 50,000N, what is the stress at failure at point O? %3D P 200mm 200mm 200mm Point O 600mm R1 |R2
Give the correct answer and solution of the problem. For the stress soil element shown, determine the following using the Pole Method. A. The major principal stress B. The minor principal stress C. Normal stress on plane AE D. Shear stress on plane AE
The vertical compressive stress at a point in a soil is 100 kN/m2 while the horizontal compressive stress at the same point is 62 kN/m². Both stresses are principal stress. (a) Draw the Mohr circle that describes the 2D stress state at the point (hand sketch is ok). (b) Find the maximum shear stress that acts at the point. (c) Determine the angle of the plane on which the maximum shear stress acts and obtain the normal stress on that plane (Use the pole method - the method is simplified since the stresses given in the problem are principal stresses). (d) Confirm the maximum shear stress and the normal stress from (c) using the stress transformation equations (consider sign conventions!).
determine the maximum shear stress. sketch thesection stress distribution
EB and FG are two planes inside a soil element ABCD as shown in Figure 10.50. Stress conditions on the two planes are Plane EB: EB = 25 kN/m2; EB = +10 kN/m2 Plane FG: FG = 10 kN/m2; FG = 5 kN/m2 (Note: Mohrs circle sign conventions for stresses are used above) Given ; = 25, determine: a. The maximum and minimum principal stresses b. The angle between the planes EB and FG c. The external stresses on planes AB and BC that would cause the above internal stresses on planes EB and FG
Determine the stress components at point A and point B. And show the stress states for these points on volume cubic elements given below. Point A y y 2 kN -------. 6 тm 10 kN 150 mm y Point B A B X
- [Mohr's Circle]. . For the stressed soil element shown below, determine a. Major Principal Stress in psi. b. Minor Principal Stress in psi. c. Normal Stress at Failure Plane AE in psi. d. Shear Stress at Failure Plane AE in psi. 150 psi 60 psi 90 psi 60 psi 45 A B.
The normal and shear stresses acting on one plane passing through a point in a soil mass are 120 psi compression and 25 psi, respectively. On an orthogonal plane the stresses are 40 psi compression and 25 psi. (a) Draw the Mohr's circle for this stress condition. (b) What are the principal stresses?
90 MPa For the shown 2D stress element, sketch Mohr circle then, use Mohr circle to find the normal and shear stresses at a point on the indicated inclined plane. 105 MPa 140° 30 MPa Verify your results (ơn, Tnt) using stress transformation eqns. Illustrate the following on Mohr circle: center of Mohr Circle, reference point A, principle stresses, max in-plane shear stress, inclined plane, orientation of inclined plane) :)
At a point P, the rectangular stress components are: x = 1, y = -2,0 = 4, y = 2, T = -3 and T = 1 yy all in units of kPa. Find principal stresses and check for invariance.
Show the type of stress distribution over the radius of the disk 3. How is the correspondence between th 象

For the element below, determine, a) Principal stresses b) Orientation of Principal stress planes c) Determine stresses on a plane inclined at 30° with horizontal d) Find maximum shear stress and its orientation Oz = 8 kPa %3D Tzx 4 kPa Txz = 4 kPa Ox = 6 kPa 30°