Another way of testing flexure strength is by quarter point loading as shown. The samplesection is 150mm x 150mm. If both P = 50,000N, what is the stress at failure at point O?%3DP200mm200mm200mmPoint O600mmR1|R2

Answered: Image /qna-images/answer/a585f81a-9123-44c2-ba64-f2775f75f5a1.jpg

Answered: Another way of testing flexure strength…

Another way of testing flexure strength is by quarter point loading as shown. The sample section is 150mm x 150mm. If both P = 50,0OON, what is the stress at failure at point O? %3D P

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.5P: The results of a tensile test are shown in Table 1.5.2. The test was performed on a metal specimen...

See similar textbooks

Similar questions

A tensile test was performed on a metal specimen having a circular cross section with a diameter 0. 510 inch. For each increment of load applied, the strain was directly determined by means of a strain gage attached to the specimen. The results are, shown in Table: 1.5.1. a. Prepare a table of stress and strain. b. Plot these data to obtain a stress-strain curve. Do not connect the data points; draw a best-fit straight line through them. c. Determine the modulus of elasticity as the slope of the best-fit line.
The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2011in.2 in area and a gage length (the length over which the elongation is measured) of 2.000 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Determine the modulus of elasticity from the slope of the linear portion of the curve. d. Estimate the value of the proportional limit. e. Use the 0.2 offset method to determine the yield stress.
A punch for making holes in steel plates is illustratedabove. Assume that a punch having a diameter of20mm is used to punch a hole10mm thick plate. If aforce P = 120KN is required to create the hole, what isthe average shear stress in the plate and the averagecompressive stress in the punch?
The nominal stress-strain diagram for a specimen having an original diameter of 10 mm and a gauge length of 50 mm is shown below. Using the given nominal stress-nominal strain diagram, answer this question. The inset shows a detailed view of the curve at low strains. 400 350 300 250 Stress (MPa) 200 150 100 50 0 0.00 Stress (MPa) 350 kN 300 250 200 150 100 50 0 0.000 0.002 0.004 0.006 0.008 0.010 0.012 Strain 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 Strain 0.18 What is the maximum force that could be applied to the specimen before it plastically deforms?
1.5-7 The data shown in the table were obtained from a tensile test of a metal specimen with a rectangular cross section of 0.2 in.² in area and a gage length (the length over which the elongation is measured) of 2.000 inches. d. Estimate the value of the proportional limit. e. Use the 0.2% offset method to determine the yield stress. Load (kips) 0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 ܩܙ ܘ 5.5 6.0 6.5 Elongation × 10³ (in.) 0 0.160 0.352 0.706 1.012 1.434 1.712 1.986 2.286 2.612 2.938 3.274 3.632 3.976 Load (kips) 7.0 7.5 8.0 8.5 9.0 9.5 10.0 10.5 11.0 11.5 12.0 12.5 13 Elongation × 10³ (in.) 4.386 4.640 4.988 5.432 5.862 6.362 7.304 8.072 9.044 11.310 14.120 20.044 29.106
Q4) The dumbell shaped specimen is made from steel rod and is cylindrical in shape, knowing that its value for elasticity is 29000 ksi, Analyze the load which produces deflection of 0.005 inches in the specimen (b) indiviual strain at each portion in it 8 in L= 6 in L= 2 in D = 2 in D= 1.5 in D = 2 in L = 2 in
An applied torque results in a shear strain (y) of 3.75 x 103 in a solid circular steel shaft. At this strain, a portion of the shaft cross- section yields as shown in Figure 2. Determine the magnitude of the applied torque. Take G = 80 GPa and yy = 2.8125 x %3D 10-3 FIGURE 2: Plastic zone 50 mm 200 mm Elastic core
Athin rectangular plate is uniformly deformed as shown. If L₁ = 0.125 in. and L₂ =0.135 in., determine the shear strain Yxy at P. 20 in. R 14 in. O -2460 μrad O -3070 μrad O -2800 μrad O -3390 μrad O -4670 μrad L₂ x
Given: E= 29x10^6 psi A= 2in^2 Determine the deformations members AB, BC, BE, DE and DF. Please show your complete handwritten solution.
The rectangular plate is deformed into the shape shown by the dashed lines. Suppose that a = 280 mm and b = 420 mm. (Figure 1) Part A Determine the average normal strain along diagonal BD Express your answer using three significant figures. vec Figure (Eavg) BD = mm/mm Submit Request Answer 6 mm 2 mm 2 mm 16 mm Part B D C Determine the average shear strain Yzy at corner B relative to the x, y axes.. Express your answer to three significant figures and include the appropriate units. 2 mm HA B -3 mm (yB)zy = Value Units
1.5-6 The data shown in the table were obtained from a tensile test of a metal specimen with a diameter of 0.500 inch and a gage length (the length over which the elongation is measured) of 2.00 inches. The specimen was not loaded to failure. a. Generate a table of stress and strain values. b. Plot these values and draw a best-fit line to obtain a stress-strain curve. c. Use the slope of the best-fit line to estimate the modulus of elasticity. Load (kips) PI223 SIN 0 2.5 3.5 10 11.5 12 Elongation (in.) 0 0.0010 0.0014 0.0020 0.0024 0.0036 0.0044 0.0050 0.0060 0.0070 0.0080 0.0120 0.0180
Two planks of different materials are attached by a special glue as shown in the figure. Theplanks have equal widths which is equivalent to 200mm. The thickness of the planks is50mm each. Determine the normal stress acting on the wooden plank and theshearing stress of the glued area if a tensile force of 20kN is applied at both ends.