fluid mechanics, side and top views of the movement are given. Question 3:The snow-sweeper vehicle shown in Figure 3 is sweeping a snow cover using its blade. The thickness of thesnow cover cleaned by the vehicle is d = 10cm and its width is B = 1m. The density of the snow is given ass = Panow/Pwater = 0.20. The ejection pattern of the snow is shown in Figure 3. If the velocity of the vehicle is15 m/s, calculate the horizontal force on the blade of the snow-sweeper. Neglect all the frictional losses.30°Snow (S = 0.20)Elevation view30Plan viewFigure 3: The snow-sweeper vehicle.

Density is defined as the mass of the substance per unit volume. Thus, weight of the flow of a fluid…

The snow-sweeper vehicle shown in Figure 3 is sweeping a snow cover using its blade. The thíckness of the snow cover cleaned by the vehicle is d = 10cm and its width is B = 1m. The density of the snow is given as 8 = Panow/Pwater = 0.20. The ejection pattern of the snow is shown in Figure 3. If the velocity of the vehicle is 15 m/s, calculate the horizontal force on the blade of the snow-swoeper. Neglect all the frictional losses. Snow (S-0.20) Elevation view 30 Plan view

The snow-sweeper vehicle shown in Figure 3 is sweeping a snow cover using its blade. The thíckness of the snow cover cleaned by the vehicle is d = 10cm and its width is B = 1m. The density of the snow is given as 8 = Panow/Pwater = 0.20. The ejection pattern of the snow is shown in Figure 3. If the velocity of the vehicle is 15 m/s, calculate the horizontal force on the blade of the snow-swoeper. Neglect all the frictional losses. Snow (S-0.20) Elevation view 30 Plan view

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The engine room of a freighter is on fire. A fire-fighting tugboat has drawn along side and is directing a stream of water to go into the stacks of the freighter. If the speed of water jet is 20 m/sec, what angle a is needed to accomplish the task. ANS: a = deg=
A canon is used to fire a bomb with velocity 20 m/s. If angle of projection is varied from 20 degrees to 70 degrees, plot the range. At which angle this range is maximum?
4. A centrifugal pump delivers water to a height of 22 metres at a speed of 800 r.p.m. The velocity of flow is constant at a speed of 2-0 m/s and the outlet vane anglc is 45°. If the pump discharges 225 litres of water per second, find the diameter of the impeller and width of the impcller at oudet. (Ans. 375 mm: 95 mm)
a pump is delivering 160 liters per sec of water using an impeller diameter of 240 mm and operating at a speed of 1800 rpm. if the speed held constant and the impeller diameter is change to 203.2 mm, what is the new dischange og the pump in liters per second
The local Amazon warehouse is looking to increase package delivering efficiency. They are testing a new conveyor belt system. Boxes are transported from one end of the factory to the other on this conveyor belt, with a velocity of vo. They eventually reach the end of the conveyor, where they slide onto a fixed incline section with uk = 0.40. The start of the inclined section is Point A, and the end is Point B. Determine: a) The velocity of the conveyor belt if the boxes leave the incline with a velocity of 8 [ft/s] Use the following diagram. Hint: Consider a box. Find its kinetic energy at point B. Find the works done by all the applied forces to the box, from point A to B. Use principle of work and energy to find kinetic energy and velocity of the box at point A. The solution is independent of mass, but for simplicity of solution, you can consider mass as 1 slug. 20 [ft] A 15°
Why is centrifugal force frequently applied to speed up particle-fluid separation? A cyclone is designed to collect dusts. Increasing gas flow rate at the inlet can increase the efficiency without changing the cyclone. How much must the flowrate increase in volume flow if the critical particle diameter is reduced to half? A centrifuge needs a 300 times of gravity acceleration for a separation. The radius of the bowl is 0.1m. What is the minimum rotating speed N (rev/min) in this centrifuge?
4 mm drill holes in the large water tank causing water to flow out of the tank into a single propeller with arc angle = 180 degrees as shown in Fig. Assuming no friction is involved, calculate 1) The velocity of the water flowing out of the borehole (V) 2) If a single propeller is attached to the ground (U=0), what is the force against the propeller? 3) If a single propeller moves to the right with a speed U=2 m/s, what is the force on the impeller? 4) Find the power generated by the impact of the water in the case of a single propeller moving at a speed U=2 m. /s
6-The product of velocity and mass of fluid particle is known as momentum. Select one: True False
If the velocity of water is 15 meters/sec and the pressure is 120kPa on the discharge side of the pump, what is the head of the pump if the velocity is 5 meters/sec and the pressure is 80kPa on the suction side of the pump?
Two geometrically similar pumps are running at the same speed of 1000 rpms One pump has impoller diameter of 300 mm and lift water at the rate of 0.02 m3 against a head of 15 m Determine the head and impeller diameter of the other pump to deliver half the discharge.
CURVILINEAR: Cheezy placed an order for 16 cubic meters of sand. The sand was ejected from a dump truck at a 50-degree angle, with an initial velocity of 2 feet per second. Calculate the radius of curvature of the trajectory at the direction point 1m below point A. with Illustration
8. A horizontal pipe 2.0 mm in radius at one end gradually increases in size so that it is 5.0 mm in radius at the other end. The pipe is 4.0 m long. Water is pumped into a small end of the pipe at the speed of 8.0 m/s and the pressure of 2.0 bar. a. Find the speed and the pressure of the water larger end of the pipe. b. The pipe is turned so as to be vertical with the small end underneath, so the water flows upward. Find the speed and the pressure of the water at the large end of the pipe now. c. How many liters of water flows in the pipe in (a) in 1 hour?