A horizontal pipe 2.0 mm in radius at one end gradually increases in size so that it is 5.0 mm in radius at the other end. The pipe is 4.0 m long. Water is pumped into a small end of the pipe at the speed of 8.0 m/s and the pressure of 2.0 bar. a. Find the speed and the pressure of the water larger end of the pipe. b. The pipe is turned so as to be vertical with the small end underneath, so the water flows upward. Find the speed and the pressure of the water at the large end of the pipe now. c. How many liters of water flows in the pipe in (a) in 1 hour?

A horizontal pipe 2.0 mm in radius at one end gradually increases in size so that it is 5.0 mm in radius at the other end. The pipe is 4.0 m long. Water is pumped into a small end of the pipe at the speed of 8.0 m/s and the pressure of 2.0 bar. a. Find the speed and the pressure of the water larger end of the pipe. b. The pipe is turned so as to be vertical with the small end underneath, so the water flows upward. Find the speed and the pressure of the water at the large end of the pipe now. c. How many liters of water flows in the pipe in (a) in 1 hour?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Please give detailed explanations and show your work clearly - I will be using this to study for an…

A: The Navier–Stokes equations contains a set of differential equations which describes the motion of…

Q: Problem 2 (33) The figure shows the vertical wall of a very large tank of water. The fluid flows…

A: Step 1: Let the distance on the ramp where the stream hits from the base of the tank be R. Using the…

Q: A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing…

Q: Figure 4.1 depicts a large reservoir of water. Water is released slowly from the reservoir, such…

Q: A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing…

Q: Helium (Molecular Weight = 4) is pumped into a 20-ft3 tank until the pressure is 149.7 psia. When…

Q: A piping system has a Y-configuration for separating the flow as shown in Figure 4. The diameter of…

A: Given data:

Q: As part of a processing of biofuels, water is pumped into a circular tank with a diameter Dt, as…

A: For the solution refer below images.

Q: Question 2: A Pelton wheel turbine is used in a hydroelectric plant to generate electric power. In…

A: The velocity diagram for the symmetrical blade of a Pelton wheel is given below,

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

Q: Task 3 Gas, evolved as a result of a chemical reaction, sequentially flows from the retort A into…

A: Pressure: Since the tension is pushed per unit region, it is relative to push straightforwardly and…

Q: What is the velocity of the pipe center (m/s)? Given that h3=68.9 cm h2 =7 cm h =3 cm Water .

A: given data: difference in head at pitot tube be h; according the question h = h3 h = 0.689m taking,…

Q: What is the velocity of the pipe center (m/s)? Given that h3=47.1 cm hy =7 cm h =3 cm Water

A: Solution:

Q: f the velocity of water is 15 meters/sec and the pressure is 120kPa on the discharge side of the…

A: Given:At discharge side of the pump:V2=15 m/sP2=120 KPaAt suction side of the pump:V1=5 m/sP1=80 KPa…

Q: 3. Determine the value of Q₁, Q₂, Q₁, d₁, Q4 and v₁ when water flows through the pipes which are…

Q: Find the diameter of the pipe in mm. The discharge of the pipe is 35 lit/sec with the velocity of…

Q: Guava juice enters a pipe with an ID of 3.05 inches at a rate of 15.6 ft3 / hr, then exits through a…

Q: if the velocity of a liquid is 1.65 ft / s in a 12-inch diameter conduit. What is the velocity in a…

Q: Q2/ A pipe with a radius of 15 mm is attached to a garden hose with a nozzle. If the velocity of…

Q: Determine the relationship between the air pressure in the tank and the maximum height to which the…

Q: What is the rate of flow of water if the actual inside diameter is 1.5 inches and the flow pressure…

Q: 8.61 cally through a 200-fi-long, 1.0-in.-diameter drawn tubing at a rate of 0.060 ft'/s if the…

A: Given that, Length of pipe, L=200 ftL=60.96 m,Diameter of pipe, d=1 in,Volume flow rate of water,…

Q: 2-the discharge through the pipe shown in fig. below is 0.4m'sec and the pressure head for point A…

Q: Problem 5: Given a Crucible with a base diameter (Din)of 8 mm and the length (L) of the attached…

Q: A rotary pump draws oil from (tank 1) and delivers it into (tank2), the level in (tank 1) is 3 m…

Q: At constant temperature, the volume of the increases from 40 L to 60 L, what is the suction pressure…

Q: The pressure through a section of pipe is 21 PSI and the velocity of the fluid is 1 ft/sec. If the…

A: given data; pressure at section 1st (P1)=21PSI=144789.903pavelocity at section…

Q: A brand of toothpaste is made using a mixture of white and red paste. During the manufacturing…

Q: As part of a processing of biofuels, water is pumped into a circular tank with a diameter Dt, as…

A: For the solution refer below images.

Q: 1. Two round pipes have water flowing through them. Pipe B is half of the diameter of pipe A. If the…

Q: A stream of water, 3” in diameter, discharges into the atmosphere at a velocity 80.0 ft/sec. Find…

Q: A pipe with a radius of 9 mm is attached to a nozzle. If the velocity of flow in the pipe is 2 m/s,…

Q: On average, you inhale approximately 1 L of air every 2 seconds. The pressure difference between the…

A: Given:To find:

Q: A centrifugal pump running at 1859 rpm has impeller dimensions of b₁ = 53, b₂ = 21, r₂ = 285, r₁ =…

A: Given Data The width of the uniform blade 1 is: b1=53 mm=0.053 m The width of the uniform blade 2…

Concept explainers

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.

Question

8.
A horizontal pipe 2.0 mm in radius at one end gradually increases in size so that it is 5.0 mm
in radius at the other end. The pipe is 4.0 m long. Water is pumped into a small end of the
pipe at the speed of 8.0 m/s and the pressure of 2.0 bar.
a. Find the speed and the pressure of the water larger end of the pipe.
b. The pipe is turned so as to be vertical with the small end underneath, so the water
flows upward. Find the speed and the pressure of the water at the large end of the
pipe now.
c. How many liters of water flows in the pipe in (a) in 1 hour?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A vertical cylindrical container contains 5840 gallons of gasoline and is 1.53 m in radius. Due to evaporation within the tank, the pressure on the top of the fluid is 2.5 times normal atmospheric pressure. The density of gasoline is 737 kg/m3. a. What is the pressure at the bottom of the tank? b. If a nozzle at the bottom of the tank is used to let fuel out, with what velocity would the gasoline exit the hole? c. If a nozzle at the bottom of the tank is used to let fuel out, what volume flow rate will result if the diameter of the hole is 1.2 cm? d. At what initial rate will the height of the fuel level in the tank drop as fuel is removed?
3. As shown in the Figure 12, for the variable speed cylinder, a and b are the oil inlet and c is the oil return port. It is already known that D=200 mm, d1=160 mm and d=40mm. The flow rate of the hydraulic pump is q=60L/ min. Calculation: the velocity of the piston when the pump only supplies oil to port a and the velocity of the piston when it supplies oil to port a and b at the same time. Figure 12
The pressure through a section of pipe is 23 PSI and the velocity of the fluid is 3 ft/sec. If the velocity was increased to 5 ft/sec, what would the pressure drop be?
1. Water enters through a 23.616 inches diameter pipe under a pressure of 14 kPa. It leaves through a 900mm diameter exhaust pipe with a pressure of 4 kPa. A vertical distance of 8.2 ft separates the centers of the two pipes at the sections where the pressures are measured. If 500 liters of water pass the motor each second, compute the power supplied to the motor.
The volumetric capacity of hydrostatic pump is more than that of a non-positive displacement pump. Select one: True False
4. Consider a following figure where water goes through an oddly shaped channel. The top passage is a cylindrical tube with diameter 5 m. The bottom tube is also a cylindrical tube with diameter 10 m. 5m 30 m 100 m 20 m 10 mi a. Find the speed of water flow on the vertical tube with diameter 5 m. b. Find the speed of water flow on the horizontal tube with diameter 10 m. c. If we were to seal the horizontal tube, what is the minimum force the sealant should handle? d. What will happen to the speed of the water through vertical tube if its diameter is increased? B
If a pipe with flowing water has a cross-sectional area nine times greater at point 2 than at point 1, what would be the velocity at point 2 if the velocity at point 1 (2 m/s)?
Title of the book: Fluid Power, Theory and Applications, 3rd Edition, James A. Sullivan
Q1) Using a system similar to that shown in figure, compute the required air pressure above the water to cause the jet to rise h2 = 41 m from the nozzle. The depth h, -2.1 m. Air pressure
Q2' A pipe with a radius of 15 mm is attached to a garden hose with a nozzle. If the velocity of flow in the pipe is 4 m/s, what is the velocity of the flow at the nozle when it is adjusted to have a diameter of 16 millimeters, and what is the flow rate?
Hydraulic Machines I need the answer in 1 hour
show dolution and diagrams.