The small car, which has a mass of 21.7 kg, rolls freely on the horizontal track and carries the 4.4-kg sphere mounted on the light rotating rod with r=0.56 m. A geared motor drive maintains a constant angular speed 0 = 2.8 rad/s of the rod. If the car has a velocity v = 0.45 m/s when 8=0, calculate v when = 53°. Neglect the mass of the wheels and any friction. Answer: When 8 = 53°, v = m/s

The small car, which has a mass of 21.7 kg, rolls freely on the horizontal track and carries the 4.4-kg sphere mounted on the light rotating rod with r=0.56 m. A geared motor drive maintains a constant angular speed 0 = 2.8 rad/s of the rod. If the car has a velocity v = 0.45 m/s when 8=0, calculate v when = 53°. Neglect the mass of the wheels and any friction. Answer: When 8 = 53°, v = m/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The question is in the picture. Thanks
The particle of mass m = 2.5 kg is attached to the light rigid rod of length L = 1.27 m, and the assembly rotates about a horizontal axis through O with a constant angular velocity = w = 3.2 rad/s. Determine the force T in the rod when 0 = 36°. The force Tis positive if in tension, negative if in compression. L Ꮎ m
The trailer has a mass of 400kg and the mass center at G. is being pulled by a horizontal force of magnitude of F = 800N. Determine the acceleration of the trailer, as well as the normal forces (Na and Nb) on the pair of wheels at A and B respectively. Assume the wheels are free to roll and have negligible mass.
The four-wheel-drive all-terrain vehicle has a mass of 300 kg with centre of mass G. If all four wheels (front and rear) are observed to spin momentarily as the driver attempts to go forward, vehicle reaches speed of 50 km/h after 60 m. At first determine the acceleration of this vehicle? Then if coefficient of friction between the tires and the ground is 0.40, determine the combined normal force at the pair of front tires. 805 mm 440 mm Figure 11 500 mm
Problem 6: The rear wheels of the truck shown provide traction force of 2000 N. If the truck has a mass of 1900 kg, determine the its acceleration and the normal force exerted on each pair of front and rear driving wheels. Also, find the time needed for the truck to achieve a speed of 20 m/s starting from rest. The front wheels are free to roll. Neglect the mass of the wheels. 2 m +1.5 m-
M = A frisbee is thrown such that its final angular velocity is w = 9 after being in flight for t = 2 s. As it rad S flies, the wind applies a constant moment, causing the frisbee to rotate faster. If the frisbee was initially at rest, determine the moment of the wind and the work done by said moment. Assume the frisbee can be modelled as a disk with mass m = = 0.15 kg and that it rotates about its center of gravity G. The frisbee has a radius of r = 0.12 m. UM = N.m r J G M
Member AB is uniform and has a mass of 150 kg. It is released from rest in the position shown, and the spring has an initial tension of 500 N. When member AB is horizontal it has a clockwise angular velocity of 2.00 rad/s. Calculate the force constant of the spring if the guide blocks A and B are massless.
3/156 The two 1.5-kg spheres are released from rest and gently nudged outward from the position = 0 and then rotate in a vertical plane about the fixed centers of their attached gears, thus maintaining the same angle for both rods. Determine the ve- locity v of each sphere as the rods pass the position 0 = 30°. The spring is unstretched when 0 = 0, and the masses of the two identical rods and the two gear wheels may be neglected. 1.5 kg 240 mm 240 mm k = 60 N/m 80 mm Problem 3/156 1.5 kg
The 16-Mg truck hauls the 37-Mg trailer. If the unit starts from rest on a level road with a tractive force of 21 kN between the driving wheels of the truck and the road, compute the tension T in the horizontal drawbar and the acceleration a of the rig. Answers: T = a = i 37 Mg KN m/s² 16 Mg
The weight of the spring held follower AB is 0.367 kg and moves back and forth as its end rolls on the contoured surface of the cam, where r = 0.2 ft and z = (0.1sin20) ft. If the cam is rotating at a constant rate of 6 rad/s, determine the force, in lb, at the end A of the follower where 0 = 45°. In this position, the spring is compressed 0.4 ft. Neglect friction at the bearing C. Round your answer to 3 decimal places. 6 = 6 rad/s 0.2 ftX z = 0.1 sin 20 Z A k = 12 lb/ft с B
2. The spheres have a mass of 7.50 kg each and are moving at v = 3.50 m/s at time t = 0 as shown. The shaft and frame have negligible mass. A time dependent driving moment M=4-t² is applied. Calculate the speed of the spheres at time t = 6.00 s. M 0.5 m
1. The spool has a mass of 50 kg and a radius of gyration ko = 0.280 m. If the 20-kg block is traveling downward at a speed of 4 m/s, determine the total kinetic energy of the system at this instant. 0.3 m 0.2 m