Q 3. The single-phase half-wave rectifier is supplied directly from a 120-V (rms), 60-Hz source through a step-downtransformer with turns ration10 : 1. The load resistance RL, is 10 N.Determine (a) the average output voltageVolav), (b) the average load current I(av), (c) the rms load voltage Volrms), (d)the rms load current I(rms), (e) the ripple factor RF of the output voltage, (f) the rms ripple voltage Vr(rms), (g) theaverage diode current Ip(av), (h) the rms diode current Ip(rms), (i) the peak inverse voltage PIV of the diode, (j) theaverage output power Po(AC), (k) the DC output power Po(DC), and (I) the frequency fr of the output ripple voltage. (

Answered: Image /qna-images/answer/b4984062-02d4-4463-9581-cc0b70ed6aec.jpg

The single-phase half-wave rectifier is supplied directly from a 120-V (rms), 60-Hz source through a step-down sformer with turns ratio n = 10 : 1. The load resistance RL is 10 N. ermine (a) the average output voltageVo(av), (b) the average load current Io(av), (c) the rms load voltage Vo(rms), ms load current I(rms), (e) the ripple factor RF of the output voltage, (f) the rms ripple voltage V(rms), (g) the age diode current Ip(av), (h) the rms diode current ID(rms), (i) the peak inverse voltage PIV of the diode, (j) the age output power Po(AC), (k) the DC output power Po(DC), and (1) the frequency f, of the output ripple voltage. (d)

The single-phase half-wave rectifier is supplied directly from a 120-V (rms), 60-Hz source through a step-down sformer with turns ratio n = 10 : 1. The load resistance RL is 10 N. ermine (a) the average output voltageVo(av), (b) the average load current Io(av), (c) the rms load voltage Vo(rms), ms load current I(rms), (e) the ripple factor RF of the output voltage, (f) the rms ripple voltage V(rms), (g) the age diode current Ip(av), (h) the rms diode current ID(rms), (i) the peak inverse voltage PIV of the diode, (j) the age output power Po(AC), (k) the DC output power Po(DC), and (1) the frequency f, of the output ripple voltage. (d)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The Figure 2 shows an electronic circuit designed for supplying power to a load (R1). The supply voltage 235V (RMS, AC) at frequency of 50HZ. The required DC voltage and power for the load are 24V and 3.6 W respectively. The Electrical Components of this AC to DC converter are: A full-wave rectifier to convert AC voltage to DC voltage. A regulator with transistor and Zener diode to ensure a constant voltage and power for the load. D1 Iide 91 Vaut VLoad D2 D3 Vde VI sine R1 RL Regulate Reetifier Figure 2. Complete Circuit Assume that the diodes are real diodes (NOT ideal diodes). The following information is available: The collector to base resistor of the regulator R1 = 5.0 k The transistor Q1 with B value of 24 is used for the regulator circuit. Determine the following quantities for this electronic device and fill the table below: Question Answer The voltage of Zener Diode (Vz) The current in R1 The DC current into the regulator | (Idc) Base current of transistor (IB) Collector…
H.W:- For a single phase half wave uncontrolled rectifier if the input supply voltage is (v= 310 sin314t), at frequency (f= 50 Hz). Then determine the followings:- Vm. Vmean- i. Draw the rectifier circuit. un %3D ii. Draw the input and the output voltages waveforms. iii. Determine the mean and rms values of the output voltage. s Ec iv. If the load is (R=10 S), then determine the mean and rms values of the current. 2019
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
Design a single-phase full wave bridge rectifier with input voltage of 100v and inductive load of 10ohm and 40mH a. Show the waveform relation between the I/P and O/P b. Calculate the average O/P voltage c. Calculate the rms current
Note: Answer All question 1: A) For a single-phase half-wave uncontrolled rectifier with (RL) load, find the rms value of the output voltage (V) and form factor (FF%) with supply voltage: v,(t) = 10 sin(wt). Draw the circuit diagram and sketch the voltages and current waveforms. The conduction angle B = 220°. %3D
For the single phase half-wave rectifier, the source is a sinusoid of 120 V rms at a frequency of 50 Hz. The load resistor is 5ohm. Determine (a) the average load current, (b) the average power absorbed by the load and (c) the power factor of the circuit.
Be a single-phase half-wave rectifier with an RL load. The sinusoidal input voltage has a frequency of 60 Hz and the value of R = 10 ohms. What is the value of L for the current extinction angle to be 270°. Tip: use Puschlowski's abacus.
PROBLEM SET 1. Derive the formula for the RMS value for the following a) b) 3m 2. Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave. 3. Following the analysis applied to the half-wave rectifier with capacitor filter, show how to arrive at the output waveform for a center-tapped full-wave with filter capacitor. See output waveform on page 90. 4. Given: Half-wave rectifier; transformer secondary voltage = 32 V; Capacitance 4700 µF; average load voltage 18 V. Determine ripple factor and average load current 5. Design a half-wave rectifier with a capacitor filter that will deliver to the load an average voltage is 15 V at 280 mA. Ripple should not be higher than 5%. 6. Given: The input to a voltage regulator circuit varies from 11.4 to 12.2 V. The load voltage is to be maintained at 9.1V with maximum…
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consisting series connected a resistor and an inductance from a 70.7V (RMS), 50HZ sinusoidal AC source. The firing delay of the thyristor is 90° and the load values are R=10Q, L=0.1 H. Define the load current expression and draw the load current by calculating for first two periods. And calculate the average values of the load voltage and current.
H.W3 The single-phase full wave controlled rectifier has a R-L load with R= 0.552 and L= 6.5mH. The input voltage V, 220V at 50Hz. The delay angle is a-30, plot the input and output waveforms. Then determine: -The average thyristor current -The rms thyristor current -The output rms current -The average output current - The efficiency NOTE: Drive any formula that used in solution
8 5. In a single-phase diode bridge rectifier circuit fed by a source voltage of 240 50%THD and a fundamental of 10A(rms). The power drawn is 2kW, Calcu a) The DPF b) The distortion current Idistortion c) The total current Is J The PF
For a full wave controlled rectifier with pure resistive load (R=100),the supply voltage is (V-50Sin314t). When the firing angle (a =0%) determine the followings: 1) The mean (dc) value of the load current. 2) The RMS value of the load voltage.