The simply supported beam consists of a W21x 44 structural steel wide-flange shape [E = 29,000 ksi; 1-843 in.). Assume that support at D can provide resistance either up or down. For a loading of w-6.7 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB= 12 ft. Lac Answers: (a) VA (b) vc= LAB i i B 5 ft. LcD=5 ft. Loe 4 ft. Lac LCD in. D in. LDE E

The simply supported beam consists of a W21x 44 structural steel wide-flange shape [E = 29,000 ksi; 1-843 in.). Assume that support at D can provide resistance either up or down. For a loading of w-6.7 kips/ft, determine: (a) the beam deflection VA at point A. (b) the beam deflection vc at point C. Assume LAB= 12 ft. Lac Answers: (a) VA (b) vc= LAB i i B 5 ft. LcD=5 ft. Loe 4 ft. Lac LCD in. D in. LDE E

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

C):-The rigid bar BDE is welded at point B to the rolled-steel beam AC. For the loading shown, determine (a) The slope at point 4. (b) The deflection at point B. Use E 200 OP 20 kN/m AT 24*2 s mid-1.5ml-1.5 m
For the beam below, determine the following, assume EI is constant. What is FEMBC in k-ft? O-96 -69 2 k/ft Select the correct response: -18 24ft 96 B ₁12k 8ft 4ft
C):-The rigid bar BDE is welded at point B to the rolled-steel beam AC. For the loading shown, determine (a) The slope at point. 4. (b) The deflection at point B. Use E 200 OP t I smp-1.5 20 kN/m 60 kN
The beam shown has the following properties: steel cover=60mm, f'c=21 MPa, and fy=420 MPa. Determine the ultimate moment capacity of the beam in kN-m. Determine also the type of failure and the beam condition (under-reinforced, over-reinforced or balanced condition) 250mm 2-Ø20mm 3-025mm h = 450mm 50mm
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E - 29,000 ksi; I - 843 in."1. Assume that the support at D can provide resistance either up or down. For a loading of w- 6.7 kips/ft, determine: (a) the beam deflection Va at point A. (b) the beam deflection vç at point C. Assume LaB = 8 ft, Lec=6 ft, Lco- 6 ft, Log = 7 ft. B. LAB Lạc Lep LDE Answers: (a) va- in. (b) vc- in.
The rigid bar AD (figure STR-4) is supported by two steel wires of 1.5mm diameter (E = 200 GPa) and a pin and bracket at D. Knowing that the wires were initially taut. Determine the following: a. The additional tension in wire BE when a load P=900 N is applied at D. b. The additional stress in wire FC when a load P = 900 N is applied at D c. The corresponding deflection at point D.
Acantilever beam AB, loaded by a uniform load (see figure), is applied on a channel section. If the cross section has the dimensions indicated and the moment of inertia about the z axis (the neutral axis) is I= 3.36 in" Find the maximum tensile stress fhtMAX and maximum compressive stress facMAX (Note: Draw the shear and moment diagram). 2.5 lb/ft 0.617 in. Z- C 2.269 in. 6.0 ft
Task 12 Z A C B 2a a a The figure above shows a static indeterminate beam ABCD. The beam has a fixed joint bearing in A and a sliding bearing in B and C. Note that the beam is continuous at point B and that the joint in the bearing is below the beam. The beam is subjected to an evenly distributed load q between A and C, while there is a point load F at point D. The beam is made of steel with an E-module E = 210 000 MPa and has a cross section with a second area moment ly = 12x106 mm4. The value of the evenly distributed load q and the length a are determined from: 9= ID+25 20 kN/m ID+40 a= m 50 ID=40 a) Determine how much the maximum force can be when the bearing in point B can withstand a maximum vertical force of 50 kN (Bz< 50 kN). Write your candidate number on all the sheets you upload. b) Now set the force F to the value you found in question a) and decide how big the deflection of the beam will be in point D, under the point load F. Write your candidate number on all the sheets…
JC = For the beam and loading shown, determine (a) the deflection at C, PL 0 A P Bt² 2 EI (b) the slope at end 4. PL ↑P -L/3L/3L13 EI D
The simply supported beam consists of a W21 x 44 structural steel wide-flange shape [E = 29,000 ksi; 1-843 in.4]. Assume that the support at D can provide resistance either up or down. For a loading of w=4.5 kips/ft, determine: (a) the beam deflection VA at point A (b) the beam deflection vc at point C. Assume LAB 10 ft, Lac-6 ft, Lcp 6 ft. Loe-7 ft. Answers: (a) VA= (b) vc= LAB B 651.06 390.3 Lac D LCD in. in. LDE E
> A Pinned- T -15 ft- 2 k/ff V V Roller утв -6ff- EI = Constant E = 29,000 ksi I = 3,500 in 4 Find: Maximum Vertical Deflection in the beam Method Ć unsupported joint using conjugate beam 2/9
A flanged cross section is Used to suppaut the lcads shown on the beam on the ext page. The dimen glons oF the ghape are given. Congider the entire om length g Hhe beam and defermine. a:) he maximum tengion bending stres at along he beam and, any location B) te maximum compreggion ben ding stress at any Jocatien along the beam. 20am l00 mm 4.5 YN JOmm Is kN Im 310 mm 270mal AI 1. 5m 1.2m 1o mm 20nm