The average normal stresses developed in section a - a of the turnbuckle, and the bolts shanks at B and C, are not allowed to exceed 15 ksi and 45 ksi, respectively. Determine the maximum axial force P that can be applied to the turnbuckle. Each bolt shank has a diameter of 0.5 in. P B I a ||-1 in.:-|| 0.25 in.

The average normal stresses developed in section a - a of the turnbuckle, and the bolts shanks at B and C, are not allowed to exceed 15 ksi and 45 ksi, respectively. Determine the maximum axial force P that can be applied to the turnbuckle. Each bolt shank has a diameter of 0.5 in. P B I a ||-1 in.:-|| 0.25 in.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The average normal stresses developed in section a a of the turnbuckle, and the bolts shanks at B and C, are not allowed to exceed 15 ksi and 45 ksi, respectively. Determine the maximum axial force P that can be applied to the turnbuckle. Each bolt shank has a diameter of 0.5 in.
Two horizontal 5.39-kip forces are applied to pin B of the assembly shown. Knowing that a pin of 1.01-in. diameter is used at each connection,determine the bearing stress (in psi) at Bin member AB.
10 mm | | | | 10 mm 50 mm ارت - 50 mm 10 mm 20 kN B 150 mm 910 mm 10 kN D ------- 150 mm Two vertical forces are applied to a am of the cross section sh vn. Determine the maximum tensile and compressive stresses in portion BC of the beam.Show your complete solution and box your answer.
The lap joint is fastened with four 3/16-in.-diameter rivets. The working stresses are 58 ksi for the rivets in shear and 10 ksi for the plates in bearing. in.
Practice 4.1.7 Two identical 20-mm - 200 mm thick plates are bolted to the top and bottom flange to form the built-up beam. 20 mm a) If the beam is subjected to a shear force of V = 250 kN, determine the allowable maximum spacing s of the bolts to the nearest mm. Assume each bolt has a shear 10 mm 300 mm capacity of 30KN, and I = 307.5E-6 m*. 10 mm b) What is the M, (plastic moment) of the beam assuming bolts can take infinite shear and o, = 250 MPai '10 mm 20 mm 200 mm
A joint connection is shown below. If the average shear stress in the pin must not exceed 107 MPa, determine the maximum applied load P that can be supported by the 12 mm diameter pin.
P 62.5 mm Key 55° The cast iron block with cross-sectional dimensions of 62.5 mm by 62.5 mm consists of two pieces. The pieces are prevented from sliding along the 55° inclined joint by the steel key, which is 62.5 mm long. The working stresses are 275 MPa for cast iron in bearing and 345 MPa for the key in shear. If the block is loaded with P= 282 kN, calculate the required dimension "b" of the key. Write your final answer in 2 decimal places with the unit of mm.
7. An angle ISA 150 x 75 x 10 mm thick, steel tension member is connected by its long leg to a 10 mm gussset as Use 6 mm fillet weld on the toe and the back. Take the allowable unit shearing stress for weld metal plate. s 112.5 N/mm². In the welded joint find the force taken by the weld on the back. Solution:
P 60° 3. The tension member is fastened together using a single bolt as shown. The bolt has a diameter of 0.6 in. Determine the maximum load P that can be applied to the member if the allowable shear stress for the bolts is 8 ksi and the allowable average normal stress is 12 ksi.
SOLVE FOR THE FORCE IN MEMBERS AB, AC, BC, CD, BD, BE, DE, DF & EF. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND WRITE WELL ALSO SEE LINK UNDER WEEK7 0.8m 2.4m -6KN MEMBER AB AC BC CD BD BE 2m ED DF EF 1m 8KN Av REACTION hinge) EX REACTION @roller) 3m SUMMARY OF RESULTS FORCE 1m 10KN 2.4m 3KN NATURE(I or C)
A traffic light signal pole is subjected to the weight of each traffic signal 45 lbs and the weight of the road lamp 55 lbs . The weight of lateral arms is included in the signal and lamp weights. The people is fixed and the base and is made of round structural steel section HSS 14.000 x 0.25. The details of the pole section may be obtained form the Manual of American society of steel Construction (AISC Steel Manual). Analyze the principle normal stresses and the maximum shear stresses on elements A and B located at the base in the pole as shown in the sketch below.
a. Draw the FBD b. Determine the value of P c. Determine the bearing reaction at A. D P. RA E 60° 25" C Az 14" 210 lbs -- - 20