QUESTION 3 A normal force is an axial force. Always Sometimes Never QUESTION 4 If the allowable stress is equivalent to the actual stress, the factor of safety is 0. True False QUESTION 5 The factor of safety increases the allowable load. O True False, the factor of safety decreases the allowable load. False, the factor of safety has no effect to the allowable load.

QUESTION 3 A normal force is an axial force. Always Sometimes Never QUESTION 4 If the allowable stress is equivalent to the actual stress, the factor of safety is 0. True False QUESTION 5 The factor of safety increases the allowable load. O True False, the factor of safety decreases the allowable load. False, the factor of safety has no effect to the allowable load.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid steel bar ABC is pinned at B and supported by two rods at A and C. There is no strain in the rods before load P is applied. After load P is applied, the axial strain in rod (1) is +910 uɛ. Determine the axial strain in rod (2). (1) 2,000 mm 520 mm 400 mm 1,250 mm (2)
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. C D I-KE -1.2 m-1.2 m 1.2 m B
a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam the solid steel bar has a square cross section of side b and is supported as shown. We know that density of steel is 7860 kg/m, calculate the dimension b for which the maximum normal stress due to bending is 50 MPa. L. C D VAR 2m +12m -1.2 m-1.2 m 1.2 m-
Radius = 2 Find normel stress at pointA ? Find sheun stren at point A ? pnt A in
Problem 2 The rigid bar is plnned at A and held by two flexible bars at E and C. The load P Is applled at B. The two flexible bars FE and DC each have a diameter of 1 In. The flexible bars are elastic- perfectly plastic with a yleld stress equal to 20 ksl and a yleld strain of 0.001. Determine the following: The load R, at first yleld and the corresponding deflection at B, &, The ultimate load Pu and the corresponding deflection du The permanent deflection and residual stresses in each rod if the ultimate load is removed Construct P - A curve showing yield, ultimate and permanent deformation o (ksi) 1 ft E F 1 ft1 ft 20 B P e (in./in.) 0.001 1 ft D 2 ft 1 ft A
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
3- Check the equilibrium of the material in the absence of body forces for the stress components in a circular cylinder of length L and radius r are given by: A B C Ax2 + Bx3 Cx3 -Cx2 [tii]= Cx3 0 0 -Cx2 0 0 2.0 1.0 0.5
The rigid bar ABC is supported by a pin at B, vertical steel rod at A and vertical bronze rod at C. Determine the selfweight W of the bar, the vertical movement of the bar at A and C and indicate the direction of movement. For the steel rod, allowable stress equal to 120 MPa and E = 200 GPa. For the bronze rod, allowable stress equal to 60 MPa and E = 83 GPa. Express your answer in N (Newton) for the selfweight of the bar and for the vertical movement answer in 3 decimal places and in mm (millimeter). A= 1200 mm. A= 300 mm 1.2 m 0.9 m A -0.6 m 1.2 m
Find normal stress at point P
A rectangular cantiliver wooden beam is applied by point load of 400in at free end Determine cross section area and second moment of inertia about bending axis and Draw internal effects shear and bending diagram Determine direct and shear stress at A on cross section of a-a .sketch state of stress
A beam has a hollow circular cross section 40 mm outer diameter and 30 mm inner diameter. It is made from metal with a modulus of elasticity of 250 GPa. The maximum tensile stress in the beam must not exceed 350 MPa. Calculate the following. (i) The maximum allowable bending moment and (i) The radius of curvature. A beam has a hollow circular cross section 40 mm outer diameter and 30 mm inner diameter. It is made from metal with a modulus of elasticity of 250 GPa. The maximum tensile stress in the beam must not exceed 350 MPa. Calculate the following. (i) The maximum allowable bending moment and (i) The radius of curvature.
A steel pipe is subjected to the 16-kN load shown below. Its outside diameter is 140 mm and its thickness is 7 mm. Consider that the yield strength of steel is 240 MPa. Analyze point H ONLY. Due to the pressure in the pipe, there is an 11.25-MPa (T) normal stress along x and a 22.50-MPa (T) normal stress along z of point H. A. Determine the internal forces and moments at the pertinent section through an FBD. B. Determine the stresses experienced by point H. Illustrate using a stress element. C. Determine the FS by MSST at point H D. Determine the von Mises equivalent stress at point H E. Determine the FS by MDET at point H 700 mm 16 KN 1,300 mm