Q2/ The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 15 mm and an outer diameter of 25 mm. The original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively. If after the nut on the bolt is tightened the tension in the bolt is 10 kN, determine the change in dimension of the cross-section of the bolt and the sleeve. Assume the material at A is rigid. E = 70 GPa, Emg = 45 GPa, Ga = 26 GPa, Gmg = 17 GPa. 50 mm 30 mm

Q2/ The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 15 mm and an outer diameter of 25 mm. The original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively. If after the nut on the bolt is tightened the tension in the bolt is 10 kN, determine the change in dimension of the cross-section of the bolt and the sleeve. Assume the material at A is rigid. E = 70 GPa, Emg = 45 GPa, Ga = 26 GPa, Gmg = 17 GPa. 50 mm 30 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The stepped rod is made up of two different materials A and B of lengths 80 cm and 1.2 m respectively. The diameters of materials B and A are 2.5 and 3.5 cm respectively. The modulus of elasticity of materials A and B are 250 and 150 GPa respectively. The elongation of the rod is the same for both the materials. A total tensile load of 40 kN is applied to both the materials A and B together. Calculate the load in each material.
Problem 2 The series of bars shown have their diameters from left to right decreasing by 3 mm, and lengths increasing correspondingly by 0.3 m. If the leftmost member has a diameter and length of 28 mm, 1.8 m, respectively, determine the nodal displacements, member forces and the value of P if the node where P acts undergoes a rightward displacement of 4.5 mm. E=180 GPa for all members. Use your calculator. 90 N/mm 45 N/mm 60 N/mm 30 KN -50 KN
The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 15 mm and an outer diameter of 25 mm. The original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively. If after the nut on the bolt is tightened the tension in the bolt is 10 kN, determine the change in dimension of the cross-section of the bolt and the sleeve. Assume the material at A is rigid. E = 70 GPa, Emg = 45 GPa, Ga = 26 GPa, Gmg = 17 GPa.
The timber member has a cross-sectional area of 1703 mm2 and its modulus of elasticity is 13.2 GPa. Compute the change in the total length (in mm) of the member after the loads shown are applied if x = 1.84, y = 3.63, and z = 4.11. Round off the final answer in two decimal places.
Problem 3, The metal stud punch is subjected to a force of 120 N on the handle. Determine the magnitude of the reactive force at the pin A and in the short link BC. Also, determine the resultant internal. loadings acting on the cross section at point E. B 50 mm 100 mm 4 50 mm D 100 mm 200 mm 120 N 300 min
Determine the magnitude of the pin force at A. Assume W = 750 lb, a = 2.7 ft, b = 2.0 ft, r = 6 in. a a r B A C W Answer: A = i D lb b
Members AC and AB support the 100-lb crate. Determine the tensile force developed in member (AB). 3 ft 4 ft 4 ft
Answer part a, b and c
Q2/ The 10-mm-diameter bolt is made of an aluminum alloy. It fits through a magnesium sleeve that has an inner diameter of 15 mm and an outer diameter of 25 mm. The original lengths of the bolt and sleeve are 80 mm and 50 mm, respectively. If after the nut on the bolt is tightened the tension in the bolt is 10 kN, determine the change in dimension of the cross-section of the bolt and the sleeve. Assume the material at A is rigid. Ea = 70 GPa, Emg = 45 GPa, Ga = 26 GPa, Gmg = 17 GPa. 50 mm 30 mm
Determine the magnitude of the pin force at A. Assume W = 510 lb, a = 3.0 ft, b = 2.0 ft, r = 6 in. r W C Answer: A = i a B a A D lb b
The structure is comprised of rigid bars AB and BCD supported by hinges at A and D. A steel rod at C provides additional support to the system. As shown, there is a roller connection between the bars at B. Determine the magnitude of the force P applied as shown if the vertical displacement of point B is limited to 1.5 mm. Neglect the weights of the bars.
The link AB of the pliers has the cross section dimensions 3mm x 20mm, and is made of steel with elastic modulus E= 190 GPa. Determine the value of the force F that would cause failure of the link by buckling