The Right figure shows the circuit structure diagrams of a linear power supply and a switching powersupply. 1) Compare the differences in the working methods oftwo circuit power transistors. 2) Explain the main reasons for Uinpower loss in the operation of the two circuits separately. 3)Point out the highest limit values for the efficiency of the twopower sources under ideal conditions.++15VControl/DriveControl急Uin15VT /DriveA(b)Uo+3V+_Uo3VPopel

1) The working methods of the power transistors in a linear power supply and a switching power…

The Right figure shows the circuit structure diagrams of a linear power supply and a switching power supply. 1) Compare the differences in the working methods of two circuit power transistors. 2) Explain the main reasons for power loss in the operation of the two circuits separately. 3) Point out the highest limit values for the efficiency of the two power sources under ideal conditions. Uin 15V + Uin 15V Control /Drive Control /Drive + (a) 本 (b) Uo. 3V + _U。 3V p

The Right figure shows the circuit structure diagrams of a linear power supply and a switching power supply. 1) Compare the differences in the working methods of two circuit power transistors. 2) Explain the main reasons for power loss in the operation of the two circuits separately. 3) Point out the highest limit values for the efficiency of the two power sources under ideal conditions. Uin 15V + Uin 15V Control /Drive Control /Drive + (a) 本 (b) Uo. 3V + _U。 3V p

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2.1 A regulator has a no-load output voltage of 12 V and a full-load output of 11.9 V at a load current of 140 mA. Determine the voltage regulation as a percentage change from no-load to full-load and also as a percentage change for each mA change in load current. (6)2.2 What are three types of switching regulators? (3)
QUESTION 1 Design a high efficiency 3.3 V, 5A d.c.to d.c. power converter from a 4 to 5.5 Vdc source. The maximum allowable inductor current ripple and output voltage ripple are 0.1A and 20 mV, respectively. Assume a switching frequency of 20 kHz. a) Design a suitable converter power circuit using a MOSFET switch, showing all calculation of inductor and capacitor values and drawing a circuit diagram of the final design including component values. Indicate the peak inverse voltage and forward current rating of any diode required, and the maximum drain- source voltage of the MOSFET. b) On the Schematic diagram, draw the path of the current flow during the ON time and the OFF time. c) Describe the effect of changing the values of the inductor and the capacitor in the circuit. d) What is the effect of switching frequency in the circuit? e) Draw the schematic diagram of a circuit with the output voltage higher than the input voltage.
Figure shows a composite switch consisting of a power transistor (BJT) in series with a diode. Assuming that the transistor switch and the diode are ideal, the I-V characteristic of the composite switch is
A thyristor half-wave controlled converter has a supply voltage of 240V at 50Hz and a load resistance of 100 ohms. What are the average values of load voltage and current when firing delay angle is; 1. 140 degrees. 2. 30 degrees.
A resistor Ra is in series with a voltage source Va. Draw the circuit. Label the voltage across the combination as v and the current as i. Draw and label the volt–ampere characteristic (i versus v).
Explain the working of single phase full converter for RLE load discontinous mode o operation with neat sketch, waveform and equations.
LABWhat is Peak-Inverse-Voltage (PIV)? Why is it considered important?
A 3-phase half wave controlled AC to DC converter is supplied from a 250V, supply. Assume the thyristor voltage drop to be 1.6V and the load current to be continuous. Evaluate the mean output voltage when firing angle is varied at 45(degree) , 60(degree) and 90(degree)
Question 8 Calculate the expression of the peak-to-peak voltage ripple of the step-up converter in the case of the discontinuous conduction mode using the circuit parameters.
1) AC power in a load can be controlled by using a. Two SCR's in parallel opposition b. Two SCR's in series c. Three SCR's in series d. Four SCR's in series 2) The advantage of using free - wheeling diode in half controlled bridge converter is that a. There is always a path for the ac current independent of the ac line b. There is always a path for the dc current independent of the ac line c. There is always a path for the dc current dependent of the ac line d. There is always a path for the ac current dependent of the ac line 3) Silicon controlled rectifier can be turned on a. By applying a gate pulse and turned off only when current becomes zero b. And turned off by applying gate pulse c. By applying a gate pulse and turned off by removing the gate pulse d. By making current non zero and turned off by making current zero
Explain the PWM control and duty cycle generation in phase-control of SCR
18. A dc-dc converter is to be built with the following specifications: Allowed dc input voltage range: +8 V to +18 V +24 V Output average voltage: Output voltage ripple: ±0.06 V maximum at rated load 300 W, resistive ±250 mA maximum at rated load 100 kHz Rated load: Input current ripple: Switching frequency: Common ground between input and output. a. Draw a circuit which can perform this function. b. What is the necessary range of duty ratio for each switch? c. Find circuit part values (R, L, and C) which will meet the stated specifications.