A transformer converts the 110-V, 60-Hz line voltage peak of 4,5 V. A half-wave rectifier follows the transformer to supply the power to the laptop computer modeled by a resistor of 0.4360. Determine the minimum value of the filter capacitor that maintains the ripple below 0.1 V. Assume Voon - 0.8V. Select one: O a 141 F O b. None of these Oc 3.41 F 241 F O d.

A transformer converts the 110-V, 60-Hz line voltage peak of 4,5 V. A half-wave rectifier follows the transformer to supply the power to the laptop computer modeled by a resistor of 0.4360. Determine the minimum value of the filter capacitor that maintains the ripple below 0.1 V. Assume Voon - 0.8V. Select one: O a 141 F O b. None of these Oc 3.41 F 241 F O d.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center- tapped full-wave and bridge type full- wave.
Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave.
Design a rectifier fed from 220-V line through a step-down transformer. The load requires an average voltage of 9 V and average power of 2.5 W. Use each of the three circuits: half-wave, center-tapped full-wave and bridge type full-wave. pls write legibly and show complete process of solution
A single-phase half wave uncontrolled rectifier circuit is operating with a purely inductive load and a source voltage of 100 sin (277t) V. An ideal PMMC ammeter is connected in series with the inductive load reads 20 A. Calculate the distortion factor of the rectifier. Answer Choices: a. 0.866 b. 0.707 c. 0.577 d. 0.816
In the full-wave rectifier circuit of figure, the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 230V (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di i v2 = VmSin ot RL Vs(N V1 Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V None of the above ell ell
A three phase full wave rectifier is shown below along with peak phase voltage Vm-169.7V. The load is purely resistive. The rectifier delivers Ipc = 100 A and the source frequency is 60 Hz. The DC output voltage is %3D VDc=280.7V and the output RMS voltage is equal to VRMS=280.93V. The efficiency, FF and RF are respectively equal to: Secondary D D D, R AD. Z D. D, Select one: O a. 99.83%, 100.08%, 4% O b. 99.83%, 55.08%, 4% O C. 99.83%, 100.08%, 16% O d. 87.83%, 100.08%, 4%
In the full-wave rectifier circuit of figure , the transformer has a turns ratio of 1:2. The transformer primary winding is connected across an AC source of 23oV (rms), 50 Hz. The load resistor is 50ohms. For this circuit, determine the peak-to- peak ripple in the output voltage * Di V2 = VmSin cot Vs (N Vo + V3 = VmSin ot D2 Full-wave rectifier- Circuit operation during positive half cycle 460 V 207 V 325.3 V O None of the above ell ell
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
Using an ideal diode, design a clamper circuit that result in the desired output waveform as shown in Figure Q7. Show overall analysis to justify the proposed design. 7. Vo Vi Designed Clamper Circuit - 3 V -20 - 43 V - Fiqure Q7 20
A single phase – half wave controlled rectifier with freewheeling diode is supplying a load consistingseries connected a resistor and an inductance from a 70.7V (RMS), 50Hz sinusoidal AC source.The firing delay of the thyristor is 90° and the load values are R=10Ω, L=0.1 H. Define the loadcurrent expression and draw the load current by calculating for first two periods. And calculate theaverage values of the load voltage and current.
CIRCUIT DIAGRAM : D1 IÑ4001 AC Source RL 1K Q VOUT PROCEDURES : 1. Construct the half-wave rectifier circuit as shown. 2. Monitor the input voltage using the oscilloscope. Adjust the oscilloscope to show at least two complete cycles of the input signal. Draw the input waveform in Graph 1 and measure the peak-to-peak value. Record this in Table 1. Convert this value into RMS value using the formula: 3. 4. Vp-p Vp-p P-P VRMS 2.828