The rectangular plate is subjected to the deformation shown by the dashed line. The dimensions are X 130 mm, Y= 180 mm, and Ay - 4 mm. Determine the average shear strain in the plate. Express your answer to three significant figures.

Q: What happens to a product with significant moisture when it is being dried?

A: Whenever any product(food) with a significant moisture is dried, the moisture in it gets evaporated…

Q: In sand casting process, the pattern is made of

A: Casting is a process in which liquid metal is poured into the mould of a casting and the desired…

Q: Unusual smell during machine operation is cause to problem. Select one: True False

A:

Q: Mercury will always have a hairline lift. Select one: O True O False

A: False: Grammatical mistake ('has' is place of 'have') Also, in mechanical engineering context ,…

Q: What is damped Vibration.

A: Given Data : damped Vibration.

Q: ow does concentration of solute in the solvent change with processing time in a batch extraction

A: Batch extraction, the most basic and widely used approach, is extracting the solute from one…

Q: What is a wet mounts?

A: A procedure that is performed in a laboratory to observe motile organisms in wet mounts. It is an…

Q: -Why tolerances are given to the parts? To reduce weight of the component Because it's impossible to…

A: Why tolerances are given to the parts? To reduce weight of the component Because it's impossible to…

Q: What impact does a rigorous lubrication program have on a facility?

A: The path to lubrication excellence is tough to navigate. It begins once people and organizations…

Q: When looking to upgrade your gear, what are the top three factors you should keep in mind?

A: To explain: Three factors that should keep in mind while upgrading the gear.

Q: Problem 5 point loading. Its elastic modulus E' is 100 GPa. Its both ends are pin connections: K of…

A: Problem 5 (20 pts) The shaft is subject to a compressive force without the torque and the point…

Q: True or False: Characteristics of a cast-off pattern arccannot give clues as to the kind of object…

A: True or False: Characteristics of a cast-off pattern arccannot give clues as to the kind of object…

Q: The general specification for production tubing is

A: After the casing has been run and cemented in place, production tubing is run into the drilled…

Q: How is it possible to decrease contact resistance? By using different fluids for better matching O…

A: Contact resistance is the resistance that hinders the flow of heat by conduction.

Q: how do the engine cylinders are made , make a flow chart and mention the process and types of…

A: Engine cylinders are made using casting process, where molten liquid metal will be allowed to…

Q: We need to purchase .50” thick foam with a tolerance of plus or minus 10%, what is the maximum and…

A:

Q: ne or more can be correct please select from below options  Lower operating temperatures are more…

A: In the moulding process known as compression moulding, a feeding material is inserted into an…

Q: What does the slenderness ratio serve as?

A: The slenderness ratio is defined as the ratio of effective length to the least radius of gyration.…

Q: Comparision between pulverized coal firing and stoker firing.

A: Pulverized coal firing and stoker firing are two common methods used for combustion in boilers to…

Q: When does damping occurs?

A: If a body is subjected to vibrations/oscillations and we need to reduce those, damping is done.…

Q: Is the Hotelling Rule applicable to oil?

A: Hotelling's hypothesis, often known as Hotelling's rule, states that nonrenewable resource…

Q: reate an acceptable temperature and relative humidity range for your working area.

A: The moisture content (i.e., water vapour) of the atmosphere, represented as a percentage of the…

Q: State true or false with explanation. a. Metal forming process, linear relationship between stress…

A: (a) Explanation:- In the metal forming process, the metal is disfigured by surpassing its elastic…

Q: What does the blending point mean?

A:

Q: How were the areas for part 2 found?

A: Given Data and to find: How the areas are calculated?

Q: 017 ABOUT INDUSTRIAL PIPING WHEN TO USE SPRING SUPPORTS WORKING UNDER COMPRESSION OR UNDER TRACTION?

A: The objective of the question is to understand when to use spring supports working under compression…

Q: What are the drawbacks of wet scrubbers?

A: Drawbacks of wet scrubbers are listed below

Q: Q16. A mug is to be made from alumina. Which forming method would be most suitable?

A:

Q: Name the design consideration of casing and explain any one

A: To define: The design consideration. Concept used: Casing: The essential components of sound…

Q: List and describe the properties that should be taken into consideration to select the most…

A: Wrench is a device used to turn the pipe and And used to install or remove the NUT it is fairly…

Q: In the hardness test, answer the questions 1- What happens to the sample if its thickness is less…

A: Thickness of the specimen should be at least seven times of the depth of the indentation. It allows…

Q: 20- Which of the following metals is used for the preparation of patterns in shell molding? a.…

A: Hi. as you have submitted multiple questions and not specified which question needs to be solved, we…

Q: What makes new gear special?

A: Given data:- Gear:-A gear is a mechanical device that connects two rotating shafts by transmitting…