Describe some of the measures to achieve the maintenance objectives.

Q: ii) List the benefits of good maintenance? (any three

A: Maintenance is defined as the process of running machine with least possible downtime. Maintenance…

Q: Based on typical tolerances for the traditional and non-tradibonal manufacturing processes, Identify…

A: Solution:   The Tolerance value for the following traditional and non-traditional manufacturing…

Q: How system reliability is difference from individual component reliability

A:

Q: Q11. Original design may not be A. New working principles B. New idea C. New concept D. New…

A:

Q: what would be the order of operations to make this part in the least amount of time and how would…

A: The order of operations to make this part in the least amount of time and how would you hold the…

Q: The type maintenance requires periodical inspection and testing.

A: Preventive maintenance/periodic maintenance/ planned maintenance is driven by time, meter or event…

Q: Question 20 (1) - Failure mechanisms Which of these statement(s) is/are correct? 1. A slope…

A: The ratio between a measurement of the maximum load that won't cause the stated type of failure…

Q: List four sources of engineering failures

A:

Q: 3.In property enhancing process, the shape of part is altered. Select one: True False

A: False

Q: What is the primary role of the maintenance in the organization and describe the maintenance…

A: This paper focuses on the significance of maintenance in organizations where different industries…

Q: What best describes this print? * A. Casting B. Forging C. Welding D. Machining 2.  There are GD&T…

A: First of all, In the given Engineering drawing the Rotor assembly is given and its parts are drawn…

Q: ow cost of investment for breakdown maintenance which after the occurrence of an advanced considered…

A: Yes, It is true.

Q: Question 14 The total amount that the feature on the actual part is allowed to vary from the…

A: Allowance: It is the difference between the basic sizes (difference between the hole diameter and…

Q: Endurance Limit calculations are suited for types of loading Random Static Impact Repeated and…

A: Endurance limit is the maximum value of the fully  reversed bending stress which a material can…

Q: 1. Please select the effects of vibration * Human discomfort Increase strain rate Structure buckling…

A: Vibration: Any unwanted to-and-fro motion of  the body about its equilibrium position is known as…

Q: Describe the concept of finding toughness using impact testing machine.

A:

Q: I need help with finding the E symbol thingy all the way to the total part.

A: A piece of titanium is given.F=645200 lbsTo determine:the value of symbol E

Q: What is the best way to test load/stress testing?

A: following is the answer to the above question-

Q: iii) Mention any two disadvantages of bad maintenance

A: It will decrease  lifespan of the asset .

Q: Tolerance Maximum Limit Minimum Limit 50.7 mm 49.9 mm 26.8 cm 26.6 cm 0.04 mm 0.12 mm 258.03 mm…

A: Given data

Q: What to Submit: Submit the following figures and table: • Temperature plot of steam pipe assembly in…

A: Given: THe The inner and outer diameter are The thermal conductivity of cast iron The temperature of…

Q: List 3 objectives of reliability

A: Reliability: It is the ability of any object or system to work accurately under standard conditions…

Q: The risk of damages in the life of a machine component can be eliminated by using individual…

A: This statement is (TRUE)

Q: How productivity of a well is done and which techniques/test you incorporate

A: Productivity of a well is measured using well test. It is a necessary practice in oilfields used to…

Q: 1. A material is said to be allotropic, if it has 2. a-iron in (Fe-C) system has a -------- crystal…

A: 1) Allotropy, also known as allotropism, is the property of certain chemical elements to occur in…

Q: Is it possible for an item to fail yield but not fail fatek

A: Given question : Is it possible for an item to fail by yielding but not fail by fatigue.   .

Q: What are the important scheduling requirements and considerations? in relations to Maintenance…

A: 1. Prioritization of Maintenance TasksCriticality: This involves assessing how critical a bit of…

Q: What are the different types of hardness test? Write a detailed note on each type.

A: Hardness is the ability of the material to resist scratch or indentation. Hardness is also defined…

Q: In a large printing operation, an employee using a clamp forklift truck that was transporting two…

A: This is a problem related to industrial safety. Some preventive measures should be taken to avoid…

Q: how do you write this in a feature control frame? "The cross-sectional shape of this feature must be…

A: The feature control frame is required to describe the condition and tolerances of the geometric…

Q: Where does a nonconservative force occur, so that mechanical energy is not conser OA

A: Here non conservative force occurs at point "C" that is point of contact of wheel and ground. Non…

Q: nd conformanc

A: introduction: here we have to describe about design quality and conformance quality

Q: (a). Mention the types of maintenance. Define breakdown maintenance. b). Draw the diagram and…

A: Maintenance  In general, maintenance may be described as attempts to maintain a machine's condition…

Q: Please guide me through the procedure of thoroughly testing individual components.

A: The procedure of thoroughly testing individual components.