QUESTION 1Kindly answer correctly. Please show all the necessary steps. Thank you so much in advance. Question 1A new fuel for combustion was found to have the following composition: carbon 71.6%, hydrogen4.8%, oxygen 6.3%, nitrogen 1.3%, sulphur 3.4%, moisture 3.5% and ash 9.1%. Calculate for completecombustion per kg of coal:1.1 The theoretical weight of air per kg of coal.1.2 The actual weight of air required with 60% excess air.1.3 The higher heating value (HHV) of coal.1.4 Write the complete combustion equation and estimate the lower heating value (LHV) of coal.

Given-Information:- Carbon, C = 71.6% Hydrogen, H = 4.8 %Oxygen, O = 6.3%Nitrogen, N = 1.3 %Sulphur,…

Answered: the necessary step

Engineering

Mechanical Engineering

the necessary step

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Introduction a. Write an introduction in 100 words about temperature and instruments used to measure…

A: Temperature is defined as "the degree of hotness or coldness". The most common temperature measuring…

Q: What is a microcontroller? 1. General purpose device that can be programmed to carry out a finite…

A: Given question is related to electromechanical devices and controllers.

Q: The given frame is subjected to the applied loads P and Q. Note that members ABC and CDE are…

A: Given To Find: FAF, FBG, FDG,FEH

Q: An amount of Php 4000 is deposited in a bank paying an annual interest rate of 5 % compounded…

A: Compound interest (also known as compounding interest) is the interest on a loan or deposit that is…

Q: You are requested to design the manufacturing process for this product. You have to give a full…

A: there are two part here and both the parts are welded as a joint the pipe and the sheet metal part…

Q: Instructions: In this exercise, incomplete relationships are set up among fluid conductors and…

A: To choose: The correct word or phrase to complete the relationship.

Q: 4. The surface temperature of the hot side of the furnace wall is 1200 degrees C. It is desired to…

Q: PC World stocks and sells a particular brand of personal computer. It costs the store £ 400 each…

Q: Determine the forces in members CD, CJ, and DJ. M 11' A L 8' B L 6 panels at 6' K C L J D L I E L ↑…

A: To find force in member CD,CJ,DJ

Q: 5- HB Pencil is used to fill the sheet table. O True O False 2- Choose the correct answer: Oa- A3…

A: 5. HB pencils are used in a sheet because it gives dark mark to identify the sheet table so the…

Q: Instructions: In this exercise, incomplete relationships are set up among fluid conductors and…

A: Here we have to complete the relationship among fluid conductors and connectors by choosing…

Q: A new fuel for combustion was found to have the following composition: carbon 71.6%, hydrogen 4.8%,…

Q: For #16.6 on page 669, do the followings: 1) Draw the top, the front, and the right-side…

Q: rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE…

A: Given Data : For triangular section : Load intensity(h)= 6 KN/m Distance upon which load is…

Q: (b) Liquid with a density of 800 kg/m³ flows through the pipe contraction shown in Figure Q1 (b).…

Q: I need answers to problems 7, 8, and 9. NOTE: Please stop wasting my time and yours by rejecting my…

A: The part name specified in the drawing is “BONNET SLEEVE”.

Q: I need question 7 answered pertaining to the print provided. I asked this question previously on…

A: 7. According to ASME, the revision can be made either by making the changes in the revision block or…

Q: I need these 2 parts answered pertaining to the print provided. If you can not answer all 2 parts,…

A: AP-001The diameter of the hole that is inclined 15 is ϕ0.25. It can be viewed in the section A…

Q: Show from the following data taken for the automobile test performed on a 4 cylinder gasoline engine…

Q: Develop two possible hierarchies for assembling a model from the parts given below: Top Pins…

A: Given question: Develop two possible hierarchies for assembling a model from the parts given below:…

Q: I need answers to questions 7, 8, and 9 pertaining to the print provided. Note: A tutor keeps…

A: 1.The pin referred to in revision A1 are called as ejector pins.

Q: 1. Given the following measurements (in metric and English respectively) of a metal cylinder: length…

A: as you mentioned I solved 1st. one. For solution refer below images.

Q: O I'd love ice-cream I love ice-cream

A: Correct is I love ice-cream.

Q: Please use different values. This answer you already gave me for a similar question. These values I…

Q: If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with…

A: Given Data⇒ Load intensity for rectangular section : F=4 KNm Distance upon which load is…

Q: 3. A simply supported beam is shown below. Do the following. a) Draw the equivalent load diagram. b)…

Q: In a forming process the length of material changes from 50 mm to 60 mm. Show the num true stress…

A: Given lo =50mm l=60 mm K= 210 MPa n=0.27

Q: 2. A simply supported beam is shown below. Do the following. a) Draw the equivalent load diagram. b)…

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

Q: Match the following statements with the term that best describes each statement. hooks law creep…

Q: Determine the equivalent state of stress on an element at the same point oriented 60° clockwise with…

Q: An air hockey table has dimensions as shown in the picture. 0.3m Usually, the air from the table…

A: according to the given data

Q: Read the questions again. Your answer is not what I'm asking. Please redo it. where is my FBD. Can…

A: The free-body diagram of the smaller cart is shown below.The free-body diagram of the larger cart is…

Q: complete relationships are set up among directional valve topics w in the preceding lesson. Complete…

A: Here in this question we have to complete the suggested relationship by choosing the appropriate…

Q: I need these two parts answered (Multiple Choice). If you can not answer all two parts please leave…

A: Problem 1To determine the tolerance specified for the depth of groove in the enlarged view, refer to…

Q: For the given state of stress below, 1- determine the principal stresses, the in-plane maximum shear…

A: here, for first part use the principal stress and max. shear stress equation. for 2nd and 3rd parts,…

Q: The impact test is used to find a material's it's ability to absorb energy before it fractures. O.…

A: About impact test. Impact test is used to determine the dynamic toughness material. In this test a…

Q: A 25 ft long solid steel rod is subjected to a load of 10,000 Ib. This load causes the rod to…

A: Data given - L = 25 ft = 25 × 12 P = 10000 lb ∆L = 0.477 in E = 30 × 106 psi

Q: B 20 mm- 50 mm A 20 mm 100 mm 50 mm 100 mm M = 8 kN-m

Q: I need answers to questions 13, 14, and 15 pertaining to the print provided. Note: A tutor keeps…

A: 13.Calculate the maximum material condition for the largest cylindrical part feature.

Concept explainers

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.

Question

QUESTION 1

Kindly answer correctly. Please show all the necessary steps. Thank you so much in advance.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6 Final-Answer:-

VIEW

Step by step

Solved in 6 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

I need problems 6 and 7 solved. I got it solved on 2 different occasions and it is not worded correctly. NOTE: Problem 1 is an example of how it should be answered. Below are 2 seperate links to same question asked and once again it was not answered correctly. 1. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/cadc3f7b-2c2f-4471-842b-5a84bf505857 2. https://www.bartleby.com/questions-and-answers/it-vivch-print-reading-for-industry-228-class-date-name-review-activity-112-for-each-local-note-or-c/bd5390f0-3eb6-41ff-81e2-8675809dfab1
Can you solve the problem again by taking the scale factor 13 ? Can you also draw the graphs requested in the question in the excel program?
The answer is one of the options below please solve carefully and circle the correct option Please write clear .
Can some one please help to solve this question following the directions and showing neat work and formulas. PLEASE AND THANK YOU!!!
Question 3 You are working on a design team at a small orthopaedic firm. Your team is starting to work on a lower limb (foot-ankle) prosthesis for individuals who have undergone foot amputation (bone resection at the distal tibia). You remember hearing about "osseointegration" in an exciting orthopaedic engineering class you attended at Clemson, so you plan to attach the foot prosthesis using a solid metal rod inserted into the distal tibia. You think stainless steel or titanium alloy might be a useful rod material. You decide to begin this problem by identifying typical tibial bone anatomy and mechanical behavior (as provided in the tables and image below). You assume the tibial bone can be modeled as a hollow cylinder of cortical bone, as represented in the image. You anticipate the length of the rod will be 1/2 the length of the tibia. Q3G: Critical Thinking: What would you propose to your team as the next step in this analysis? Is it reasonable to assume the rod will experience the…
I need problems 7, 8, and 9 answered pertaining to the print attached below.
I will rate you with “LIKE/UPVOTE," if it is COMPLETE STEP-BY-STEP SOLUTION. If it is INCOMPLETE SOLUTION and there are SHORTCUTS OF SOLUTION, I will rate you with “DISLIKE/DOWNVOTE.” THANK YOU FOR YOUR HELP. PS: If you have answered this already, DON'T ANSWER IT AGAIN; give chance to OTHER EXPERTS to answer it. I want to verify if all of you will arrive in the same final answer; thats why I ask it multiple times. If you answer it again, i'll DISLIKE all your entries/answers.
J 6
I need answers to questions 4, 5, and 6 pertaining to the print provided. Note: A tutor keeps putting 1 question into 3 parts and wasted so many of my questions. Never had a issue before until now, please allow a different tutor to answer because I was told I am allowed 3 of these questions.
Mark the correct definition
I need answers for problems 13, 14, and 15 pertaining to the print provided. NOTE: If you refuse to answers all 3 parts and insist on wasting my question by breaking down 1 simple question into 3 parts, then just leave it for someone else to answer. Thank you.
Choice the correct answer.