complete relationships are set up among directional valve topics w in the preceding lesson. Complete the suggested relationships by choosing the appropriate word or p at the end of the exercise. 1. on-off: 2-way/pressurize-exhaust: 2. pneumatic valve: sub-base mounting/hydraulic valve: 3. hand lever: manually operated/fluid pressure: 4. spool: hydraulic valve/poppet:

Q: : the components of the 100 lb force are B. l00 A 60 30

A: Given data: Magnitude of the force = 100 lb Need to determine the components of the force along A…

Q: Given the equation of the circle x + y? - 2x - 4y+1 = 0, find the centre of this circle. A. (-1,2)…

A: Given Data- The equation of the circle isx2+y2-2x-4y+1=0.

Q: 2. Determine the angle e between pipe segments BA and BC.

A:

Q: Determine ali fur ce of te mem bers truss Shown

A:

Q: If b = 10 in, h = 5 in, X1= 5 in, and Y1=2 in, determine the magnitude of dy that would be used in…

A: given-         b=10in, h=5in X1=5in Y1=2infind- dy

Q: A force of 1000 N acts on as bracket as shown. Determine the moment of the force about B using three…

A: To determine the moment about point B.

Q: Replace the two pairs, demonstrated by a single equivalent pair

A: Consider the diagram shown for the given structure,

Q: P2-8. set up the dot product to find the angle 0. Do not calculate the result. 3 m 2 m 2 m B

A:

Q: Determine the (f_R, By using Law of cosine when ( A=8 lb, B=6 lb, c = 100°) .A 10 .B 11lb .C 10.8lb…

A:

Q: Member AB is supported by a cable BC and at A by a square rod which fits loosely through the square…

A:

Q: In a crossed-belt drive, two sheaves have diameters of 10 in and 12in. If the center distance is…

A: Given data, Centre  distance, x= 14 in.  d1= 10 in. d2= 12 in. It is cross belt.

Q: Find forces A and B in diagram at right.

A:

Q: 3. In the figure shown, solve for the distance b. 36 kN 20 kN y 94 kN m 2 m 3 m 2 m

A: Given Data :

Q: The pipe assembly is subjected to the 150-N force(Figure 1). Part A Determine the moment of this…

A:

Q: Q- 6- Resolve the force 250N into rectangular components 250 N 16 9. 12

A: Here, Magnitude of the force = 250 N   For the given triangle, missing angle θ can be found by,…

Q: w the components of F along the u and v w the triangle with sides and angles labeled to be able to…

A:

Q: L1=4 in , L2=3 in, L3=1.5 in , h1=5 in , h2=6 in , f=7 lb , p= 45 lb. determine the proper angle in…

A:

Q: Q3) Determine the moment of the force about point O. show in Fig (3) Neglect the thickness of the…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: The x component of the cross product of the vector from C to D times the force F. (Use the format…

A: Solution:-Given dataA≡0,2,0B≡4,4,4C≡0,0,4D≡4,0,0F=105 N

Q: esultant force.

A: given:

Q: In the picture, a weight pulls on a pulley (solid disk) of mass 0.5kg and a radius of 0.25m. The…

A:

Q: Consider the pipe shown in (Eigure 1) Figure ▼ Part A Determine the coordinate direction angles a,…

A:

Q: The assembly above is constructed out of a bent circular rod with a diameter of 1 in, Which of the…

A:

Q: Determine the angle between the two ropes. 1 m 2 m 1'm 3 m B. -y •G 1 m 1m

A:

Q: Two forces L (parallel to the y-axis) and A (parallel to the z-axis) are applied at point Q on the…

A:

Q: The landing gear system of a plane is made of an actuator AC and 2 rods CB and OAB. They are pin…

A:

Q: 2. Determine the moment of the four forces acting on the rod as in the fig. about point 'o' 40 N N…

A: The free body diagram for the body is given below,

Q: 3. The uniform L-shaped bar pivots freely at point P of the slider, which moves along the horizontal…

A: Let the total mass of the L-shaped bar be 'm'. The weight acting on the different points of the bar…

Q: A moment of 260 lb-in is required to start rotating the triangular plate about the edge AC. What is…

A: Given: To find: Least force applied at B

Q: Solve the 260N force of fig as shown into two components with one acting along AB and the other…

A: Given: Force is 260 N.

Q: 4. Solve for the support reactions at A, B, and C. 3 C 3 15 4 3 BE C.G.- F E 2k 8k 16' 4' 12'

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.