The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross- sectional area of 25 mm 2 and a =11.7 *10 7 m/ m.°C. B 15 KN 0.2 m 0.2 m 0.4 m

The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross- sectional area of 25 mm 2 and a =11.7 *10 7 m/ m.°C. B 15 KN 0.2 m 0.2 m 0.4 m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: The rigid beam of negligible weight is supported by a pin at O and two vertical Rods. Find the…

Q: The compound shaft in Figure is attached to rigid supports. For Bronze G = 40 GPa and for Aluminum G…

A: Given DataFor Bronze G=40 GPaFor Aluminium G=35 MpaDiameter of Bronze=200 mm=0.2 mDiameter of…

Q: Analyze the given frame. P units in kN/m P 3m P 5m 4m pin 0.7P 4m

Q: Situation 3: The rigid bar ABC has a weight of 2 kN (acting on the mid-span) shown in Figure, is…

A: Coefficient of expansion of steel = 11.7 × 10-6 /°C Determinea. Stress in the steel rod. b. Vertical…

Q: When the two forces are placed on the beam, the diameter of the steel rod (E-200GPa) BC decreases…

Q: In the beam given below, it is subjected to a load of L= 4 m and a uniformly distributed load q=15…

Q: Determine the magnitude of the resultant force at A.

A: The given figure is shown below:

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

Q: Problem #3 Am -2 m- B -2 m- -2 m BkN C KN Y KN Determine the force in each member of the truss.…

Q: (2) (1) Pe с B L2 Li

Q: Situation 3: The rigid bar ABC has a weight of 2 kN (acting on the mid-span) shown in Figure, is…

A: Coefficient of thermal expansion = 11.7 × 10-6 /°C Determinea. Axial stress in steel rod b. Vertical…

Q: В 60° k www 45° C D E A

Q: 2/11 The two forces shown act at point A of the bent bar. Determine the resultant R of the two…

Q: 214. The rigid bars AB and CD shown in the figure are supported by pins at A and C and the 2 rods.…

Q: Determine the vertical displacement of joint C. The length, L, of trusses AC, BC is 1,100 mm. The…

Q: In the equilibrium position shown, the resultant of the three forces acting on the bell crank passes…

Q: ce in member e in member

A: degree of static indeterminacy, Ds = m+ r -2j m = total number of members r = total number of…

Q: The Steel rod, E = 210 GPa, has a diameter of 35 mm. If it is subjected to the forces shown,…

Q: 600 N/m 1 m 3 m 2 m R2

Q: The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the…

A: We will find force in Aluminium and use displacement formula.

Q: Ex,: A weight Causes a static deflection of 8.= 0.060 in ist in on a beam with sf stiffiess k=…

A: Given,Static diflection Sstatic = 0.060 in Sstatic = 0.06 x 12 ft…

Q: 3. The rigid bar AB, attached to two vertical rods as shown in Figure 3, is horizontal before the…

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

Q: The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Determine the state of…

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

Q: H.W3: Analysis the structure shown in figure, El is constant W=20 KN/m P 40 KN BL 4m 3 3.

Q: 3. The rigid bar BDE is supported by two links AB and CD. Link AB is made of steel (E=200 GPa) and…

A: Find deflection at E?

Q: The lower ends of the three steel bars in Figure are at the same level before the appliec…

A: Draw diagram Draw Free body diagram Consider the moment equilibrium about point A…

Q: 10 mm -200 mm- B

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

The lower ends of the three steel bars in Figure are at the same level before the applied
concentrated force 15 kN. Determine the force in the steel bars if the temperature is
increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross-
sectional area of 25 mm 2 and a =11.7 *10 7 m/ m.°C.
15 KN
0.2 m
0.2 m
0.4 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step by step

Solved in 4 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

3
Use X = 137 Y = 37 A = 6 B = 8 C = 1
9
7) The load P is located midway between points B and C. P = 1.7 kN. The diameter of the rod at CE is 4.8 mm. The young's modulus of the rod metal = 200 GPa. What is the elongation of the rod CE? 600 mm IB 600 mm 600 mm Elongation of rod EC = units
Use x = 137 y = 37 a = 6 b = 8 c = 1
The central rod CD of the set below is heated from T1 = 30ºC to T2 = 180ºC by an electrical resistance. At the lowest temperature, the gap between C and the rigid bar is 0.7 mm. Determine the force in rods AB and EF caused by the increase in temperature. Rods AB and EF are made of steel and each have a cross-sectional area of 125 mm2. CD is made of aluminum and has a cross-sectional area of 375 mm2. Use EFe = 200 GPA, EAl = 70 GPA, αFe = 12 x 10-6 /°C, and αAl = 24 x 10-6 /°C. answer: 5.4 kN
The cross-sectional areas of the bars in the cage system are 1000mm2 Calculate the force P so that point A has a vertical displacement of 0.85 mm. E=200 Mpa
1.) 600 lb Determine: 900 lb - The resultant force (R) - The angle 0 between the R and the x-axis 40 35°
X= 460 lb. Find the stress at points A and B. Determine the point where the neutral axis intersects like ABD. The neutral axis intersects AB at (blank) inches from A and intersects BD at (blank) inches from D.
2. The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its line of action are unknown. The resultant of this force system is the couple-vector. (-1100i + 1500J)lbft. Determine P and its line of action. %D 1400 lb 200 lb 300 1b y 2. ft 3 ft 3 ft 4 ft