3. The rigid bar AB, attached to two vertical rods as shown in Figure 3, is horizontal before the load P is applied. Determine the vertical movement of P if its magnitude is 50 kN. Aluminum L= 3 m A = 500 mm² E = 70 GPa A 3.5 m FIGURE 3 P B Steel L= 4m A = 300 mm² E = 200 GPa 2.5 m C

3. The rigid bar AB, attached to two vertical rods as shown in Figure 3, is horizontal before the load P is applied. Determine the vertical movement of P if its magnitude is 50 kN. Aluminum L= 3 m A = 500 mm² E = 70 GPa A 3.5 m FIGURE 3 P B Steel L= 4m A = 300 mm² E = 200 GPa 2.5 m C

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

Q: A beam with an overhang is supported and loaded as shown in the figure below. The beam has widths w₁…

A: Given data: w1=1 in, w2=0.4 in, h=3.2 in The given beam is statically determinate beam and can be…

Q: C. A steel column with an outer diameter of 50 mm and an inner diameter of 40 mm surrounds a solid…

Q: The beam shown is hinged at one end. It is supported by two steel rods of equal length of 1.5m.…

Q: An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the…

Q: A homogeneous steel beam is loaded from the figure below. The Cross- Sectional area of the beam and…

Q: For the assembly shown in the figure, a force of 25 kN is applied to the ring at F. Determine the…

Q: Situation 3: The rigid bar ABC has a weight of 2 kN (acting on the mid-span) shown in Figure, is…

A: Coefficient of expansion of steel = 11.7 × 10-6 /°C Determinea. Stress in the steel rod. b. Vertical…

Q: A rigid bar AB is supported by three rods. A load P = 375 kN is applied to the bar. The modulus of…

Q: 2. The bar ABCD in the given figure below consist of three (3) cylindrical steel segments, each with…

A: Finding out normal stresses at each segment.

Q: A simply supported beam of span 4 m carries a concentrated load p acting downward at distance 1.5 m…

Q: A homogeneous bar AB as shown in Figure 3.3 -3 has a uniform cross - section and weighs 300 N/m. It…

Q: The rigid beam is supported by three 25-mm diameter A-36 steel rods. If the beam supports the force…

Q: Set P = 49 kN, P₂ = 37 kN. (Figure 1) Figure P₁ N 2 m 1.5 m ▾ Part A Determine the force in member…

Q: Consider the stepped bar made with a linear elastic material and subjected to an axial load of1 kN,…

A: given- FBD-

Q: Consider the beam shown in (Figure 1). Take P = 2 kip and w = 1.9 kip/ft. Point E is just to the…

Q: An aluminum bar having a cross-sectional area of 160 mm2 carries the axial loads as shown in the…

Q: Situation 3: The rigid bar ABC has a weight of 2 kN (acting on the mid-span) shown in Figure, is…

A: Coefficient of thermal expansion = 11.7 × 10-6 /°C Determinea. Axial stress in steel rod b. Vertical…

Q: A compound bar consists of a circular rod of steel of diameter 25 mm, rigidily fitted into a copper…

Q: Aluminum [E = 69 GPa] member ABC supports a load of 25 kN, as shown in the figure. Assume L₁ = 1.5…

Q: Consider the beam shown in (Eigure 1). Set F= 65 kN. Neglect the thickness of the beam. Figure 2 m…

Q: A bar made of a metal alloy has the dimensions shown in Figure. If an axial force of P=10xb kN is…

A: E=210GPA

Q: 3P A beam ABCD made of extruded aluminum and of length L = 1000 mm, is fixed at its ends A and D.…

Q: Steel rod Steel rod A = 900 sq. mm A = 900 2 m sq. mm Copper A = 1200 2 m ww bs A B 1m 1 m

Q: 24. Determine the maximum tensile, compressive, and shear stresses at points A and B on the bicycle…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: σ=PA ----( 1 ) here σ is stress , A is cross sectional area and P is force applied Calculate σst…

Q: CLO 1: A rigid beam rests on two bronze bars 700 mm long. Another aluminum bar is placed between…

A: NOTE: As per our company guidelines for multiple questions we need answer 1st question only

Q: A beam is supported by a column 3 m tall with dimensions a x 1.5a as shown above. The column is…

A: Column length= 3m (fixed at base and pinned to the beam)column dimensions= a×1.5aE= 25 Gpaσy=20 Mpa…

Q: The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the…

A: We will find force in Aluminium and use displacement formula.

Q: Consider the stepped bar made with a linear elastic material and subjected to an axial load of1 kN,…

A: Given- Stepped bar- Axial load P=1 KN, Cross sectional areas A1=100 mm2, A2=60 mm2, Young's modulus-…

Q: structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries…

Q: The 1.16-in.-diameter rod in (Figure 1) is subjected to the loads shown. Determine the state of…

Q: A SOLID ALUMINUM SHAFT 2 INCH DIAMETER IS SUBJECTED TO TWO TORQUES AS SHOWN IN THE FIGURE. DETERMINE…

A: Given data: Diameter of shaft=2 inch Torque=T1=200 lb-ft T2=800 lb-ft It is asked to find maximum…

Q: A rigid bar AD is pinned at end A and supported by two rods at points B and C. Determine the…

Q: An extruded beam has the cross section shown. It is given that V = 48 kN. NOTE: This is a multi-part…

A: Given:-An extruded beam cross-section is given The magnitude of the shear force (V) = 48 kNTo…

Q: Consider the beam shown in (Figure 1). Take P = 2 kip and w = 1.9 kip/ft. Point E is just to the…

A: A beam is roller supported at A and fixed at C, also an internal hinge is present at B.At the…

Q: Problem 3 For the compound beam shown in Figure 4, determine the reaction forces, calculate the…

A: Given ;

Q: Determine the forces in all bars of the truss shown in the given figure. Indicate tension or…

A: The truss shown is symmetrical about its vertical axis passing through C. X = 18 kN Degree of static…

Q: 8. A rigid bar AB is supported by three rods. A load P= 250 kN is applied to the bar. The modulus of…

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: Determine stress in each section

Q: A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as…

A: To determine the stress in each section of the rod. Given, Load P = 3000 N Area of bronze, Ab =…

Q: gid beam is supported by a pin at A and two metallic wires at B and C. Determine the force P that…

A: To find value if load P

Q: If the beam is subjected to an internal moment of M = 30 kN.m, determine the maximum bending stress…

A: Given : M = 20 kN-m This is a problem of Solid mechanics where we have to find the max. bending…

Q: For the beam with coordinate shown in figure. Develop the flexibility matrix. 2 B

Question

3. The rigid bar AB, attached to two vertical rods as shown in Figure 3, is
horizontal before the load P is applied. Determine the vertical movement
of P if its magnitude is 50 kN.
Aluminum
L= 3 m
A = 500 mm²
E = 70 GPa
A
3.5 m
FIGURE 3
P
B
Steel
L= 4m
A = 300 mm²
E = 200 GPa
2.5 m
C

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Q-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E = 2 × 105 N/mm² and Ecu 1.2 x 105 N/mm². = Steel tube → Copper tube '25mm 2.5mm
Please explain how they got these values along with the steps used to find them.
QUESTION 4: Check whether the beam section whose loading condition, cross section and dimensions are given in the figure is sufficient. Also draw the shear stress diagram of the section next to the section.
A rigid bar XYZ as shown in the figure below is hinged at X and is supported at Y. If the stress in the steel rod is limited to 150 ksi, determine the largest possible load P that can be applied at point Z.
The force in DB of the truss shown in below figure is W A C O VW tension 5m √3 W compression 2 W compression 5 W tension E D 2W 5m B
Problem 8.45 The three bars have a weight of WA = 20 lb, WB = 40 lb, and Wc = 60 lb, respectively. (Figure 1) Figure 1 of 1 > CPCB=0.5 BMBA=0.3 A MAD=0.2 P D Part A If the coefficients of static friction at the surfaces of contact are as shown, determine the smallest horizontal force P needed to move block A. Express your answer to three significant figures and include the appropriate units. μA P= Value Submit Units My Answers Give Up ? Provide Feedback Continue
with explaination thanks
Q-1 A compound bar consists of a circular rod of steel of diameter 25 mm, rigidly fitted into a copper tube of internal diameter 25 mm and thickness 2.5 mm. If the bar is subjected to an axial load of 100 kN, find the stresses developed in the two materials. Given, E = 2 × 105 N/mm² and Ecu 1.2 x 105 N/mm². = Steel tube → Copper tube '25mm 2.5mm
A rectangular steel block is 4 inches long in the x direction, 3 inches longin the y direction, and 4 inches long in the z direction. The block issubjected to a triaxial loading of three uniformly distributed forces asfollows: 48 kips tension in the x direction, 60 kips compression in the ydirection, and 54 kips tension in the z direction. If ν = 0.30 and E = 29 ×106 psi, determine the single uniformly distributed load in the x directionthat would produce the same deformation in the y direction as the originalloading. Note provide a diagram/figure. -Draw and label the diagram correctly, No diagram in the solution will be marked wrong. -Shortcut solution will be marked wrong.- Direction of the assumption of the equilibrium equation must be shown, no direction will be marked wrong.