The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross-sectional area of 25 mm 2 and a =11.7 *10 m/ m.°C. -7

The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross-sectional area of 25 mm 2 and a =11.7 *10 m/ m.°C. -7

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as…

Q: Question 6 A straight bar is fixed at edges A and B. Its elastic modulus is E and cross section is…

A: A straight bar fixed at edges A & B as shown- Elastic modulus = E, Cross-section area=A, Load…

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Given data :

Q: The slender bar AB weighs 50 lb and moves in the vertical plane. The bar was initially held at rest…

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

Q: Statics of Rigid Bodies (Round off to two (2) decimal places. Include negative sign (-) if the…

A: Force F = 800 lbF acting at 40° with the rod AB.Rod AB is at angle 60° to the horizontal.

Q: The force in member AB of truss joint B shown in figure is given a 15 N B• - 10 N AB

Q: Question 2: calculate the forces in AB, BC and AC of the following Truss R kN R = Last two digits of…

A: R=6kN

Q: In the beam given below, it is subjected to a load of L= 4 m and a uniformly distributed load q=15…

Q: The bar AB is attached to aluminum and steel rods, horizontal before the load P is applied. Find the…

Q: A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E =…

Q: The sum of the two forces acting at a point is 16 N. If the resultant force is 8N and its direction…

Q: 3. Two beams are supported as shown in the diagram below, each 150mm x 200mm x 4 meters. Beam CD is…

Q: Please help with this practice question. Thanks Question 1 ) Determine the y-component of force at…

A: We are required to find the Y component of force at pin D

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and…

A: Given data Modulus of Elasticity (E) EAB = 70 GPA = 70 × 103 N/mm2 ECD = 200 GPA = 200 × 103…

Q: A Given the FLEXURAL beam shown=6000 RIGIDITY of the KN.m^2, find the :deflection at the roller…

A: Roller support is a support condition in which vertical movement is restrained while the rotation…

Q: The truss is subjected to the system of forces as shown in the following figure. The truss is…

A: Given p1=p2=4 KN degree of static inderminancy Ds=Dse+Dsi where Dse=degree of external…

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

Q: - Determine the reactions at supports A and B.

Q: The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and…

Q: The 3 bars are made of steel and form a pin-connected truss. Each bar has a cross sectional area of…

Q: Mechanics of Deformable Bodies 80 N 200 mm 300 mm B The pipe shown in the figure has an inner…

A: Solution-The given data,Innerdiameter=80mmOuter diameter=100mm80N forcesTo Determine,The shear…

Q: y P b 1500 N 240 mm 300 N 30° 120 mm 1000 N

A: The value of P and it's components can be calculated by taking horizontal forces and vertical…

Q: B) The steel rod having a diameter of 2Z mm is subjected to an internal moment of 4Y0 Nm as shown in…

Q: 2/11 The two forces shown act at point A of the bent bar. Determine the resultant R of the two…

Q: Calculate the force in member AB in kN Calculate the force in member Al in kN Calculate the force in…

A: Given- truss carrying a total load of 5F, where F=1000Kn support A is hinged and support H is…

Q: QUESTION 4 A shaft AB is attached to the beam CDFH as shown in fig Q4 below. A torque of 200 kNm is…

A: Angle of twist The angle of twist for a shaft subject to torsional loading is the rotational angle…

Q: 22 Situation 1: The 300-lb force is to be resolved into components along lines a-a' and b-b'. a 1.…

Q: The 3 bars are made of steel and form a pin-connected truss. Each bar has a cross sectional area of…

A: Given, T1=50 F T2=110 F α=6.6×10-6 ft/ft F Area,A=3 in2 Angle of bar AB from the vertical bar AD,…

Q: In the equilibrium position shown, the resultant of the three forces acting on the bell crank passes…

Q: ce in member e in member

A: degree of static indeterminacy, Ds = m+ r -2j m = total number of members r = total number of…

Q: 3: Analysis the structure shown in figure, El is constant W=20 KN/m 40 KN C. 4m

A: Given data in question UDL Point load Span member length To find out Analyze the structure The…

Q: Bar AB is rigid and is attached to the steel and aluminum rods as shown in the figure. Before the…

Q: 600 N/m 1 m 3 m 2 m R2

Q: 2) The rigid bar ABC is horizontal before the load Pis applied as shown in the figure. Determine the…

Q: 2. The magnitude of the three forces acting on the plate are F₁ = 100KN, F₂=80kN and F3= 50kN. Solve…

Q: Ex,: A weight Causes a static deflection of 8.= 0.060 in ist in on a beam with sf stiffiess k=…

A: Given,Static diflection Sstatic = 0.060 in Sstatic = 0.06 x 12 ft…

Q: Two rods vertically connect beams AB and CD as shown in the figure Point A is fixed supported while…

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

The lower ends of the three steel bars in Figure
are at the same level before the applied
concentrated force 15 kN. Determine the force in
the steel bars if the temperature is increased by
40°C. Neglect the weight of bar ACE. Bars AB,CD
and EF each have a cross-sectional area of 25 mm
-7
2
and a =11.7 *10 m/ m.°C.
E
A
15 KN
0.2 m +
0.2 m
0.4 m
of

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

T 10 in Problems 4.54-4.55 4 4.55 The bar has a solid circular cross section. Its polar moment of inertia in in is given by J = 0.1 + 0.15x, where x is the axial position in inches. The shear modulus of the material is G 4.6E6 psi. If the bar is subjected to an axial torque T = 20 in - kip, what is the bar's angle of twist in degrees? =
The rigid bar BDE is supported by two links AB and CD. Link AB is made of aluminum (E = 70 GPa) and has a cross-sectional area of 500 mm^2; link CD is made of steel (E = 200 GPa) and has a cross-sectional area of 600 mm^2. For the 30 kN force shown, determine the deflection of B and E, respectively. 0.4 m 0.3 m B A 0.2 m OC -0.4 m 30 kN E
Both wires have a cross sectional area of 17 mm? and are constructed of the same material with a modulus of elasticity of 200,000 MPa. 1. Determine the wires' tensile stress at C. 2. Determine the wires' tensile stress at D. 3. Calculate the maximum displacement possible. 900 mm 450 mm C D 500 mm 1250 mm P=1500 N 1650 mm
What is the value of the force in the member EA in N? if P = 38-N. (Note: enter your numeric answer only. No need to enter units. Give your answer to three decimal places and negative for compression). EA = P -2 m E -2 m D 1.5 m B.
H.W3: Analysis the structure shown in figure, El is constant W=20 KN/m P =40 KN B C 4m 3 3
The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross- sectional area of 25 mm' and a =11.7 *10 m/ m°C. 15 KN 0.2 m 0.2 m 0.4 m
A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E=200 GPa. If the allowable stress in rod CD is 120 MPa, what weight W in kgs can be safely applied?
The lower ends of the three steel bars in Figure are at the same level before the applied concentrated force 15 kN. Determine the force in the steel bars if the temperature is increased by 40°C. Neglect the weight of bar ACE. Bars AB,CD and EF each have a cross-sectional area of 25 mm 2 -7 and a =11.7 *1o'm/ m-°C. 15 KN 0.2 m 0.2 m 0.4 m
A steel strip is clamped at left end and supported by a spring at right end. The spring has a stiffness of k = 3 N/mm. The strip is 5 mm wide and 10 mm high. Take E = 200 GPa. A 10 mm -200 mm What is the reaction of the spring (N) 50 N B k:
3. The resultant of the force system shown is a vertical force which passes through point A. Determine the resultant. Find also the value of F and 0. 1.2 m DK 0.9 m 110 N-m AK 0.6m 90 N 0.9 m 450 N FR 1.2 m Ө C B
If the following structural beam has a rectangular cross-section and is subjected to the loadings as shown below, determine the followings: a- The vertical reactions at A and B. b- The centroid of the rectangular cross-section. c- The moment of inertia of the rectangular cross-section. d- The maximum bending moment in the beam. e- The absolute maximum bending stress in the beam.
A steel strip of length L = 200 mm is fixed at A and rest at B on a vertical spring of stiffness k = 2N/mm. The steel strip is 5 mm wide and 10 mm thick. A vertical load P = 50 N is applied at B as shown. Consider E = 200 GPa, the force (in N) developed in the spring is A L P B K