The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN, determine the magnitudes of the average normal stress in the shank, the average shear stress along the cylindrical area of the plate defined by the section lines a-a, and the average shear stress in the bolt head along the cylindrical area defined by the section lines b-b. Answers should be in MPa. 8 mm a 7 mm 8 kN 18 mm a 30 mm

The long bolt passes through the 30-mm-thick plate. If the force in the bolt shank is 8 kN, determine the magnitudes of the average normal stress in the shank, the average shear stress along the cylindrical area of the plate defined by the section lines a-a, and the average shear stress in the bolt head along the cylindrical area defined by the section lines b-b. Answers should be in MPa. 8 mm a 7 mm 8 kN 18 mm a 30 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find the diameter of dAB dec bar if the stress equal to 0.15GPA C 120cm B 125kN 125KN 90cm A 60kN
A gusset plate is connected to the flange of column with the help of fillet weld on both sides as shown in the figure. The direct shear stress and bending tensile stress are 70 MPa and 130 MPa respectively. Find the equivalent stress (in GPa). Gusset plate I-section flange
N = 7
2 please with explanation :)
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears a determine the minimum force P required to punch the slot. Punch O 1051 KN O 766 kN O 649 kN O 717 KN O 979 KN Slug Plate 20 mm 75 mm Plan view of slug + a stress of 360 MPa,
Question-02Describe the various types of stresses developed in the shaft AB due to load P acting at the end C as shownin Figure 1.
The strain at point A on the bracket has components €g = 330 (10-6), e, = 560 (10-6), Yxy = -570 (10-6), e; = 0. Correct Part B Determine the maximum shear strain in the x - y plane. = 6.15x10-4 'in-plane Submit Previous Answers Correct Part C Determine the absolute maximum shear strain. (Figure 1) Figure < 1 of 1 vec -4 Yaa = 7.99 • 10 max Submit Previous Answers Request Answer X Incorrect; Try Again
A Single rivet lap joint is to commect 12 mm thick plates by providing 20mm dia. rivet at so mm pitch. determine the strength of the joint and joint efficiency. Take working stress. in shear in rivets = 80N/mm², working stress in beaning in rivets = 250 N/mm² and working stress in axial tension in plates = 150 N/mm².
6
During the tension test, the wooden specimen is subjected to an average normal stress of 2 ksi. Determine the axial force P applied to the specimen. Also, find the average shear stress developed along the section Ɵ -a of the specimen.
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Мра. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm F F mm. 50 mm 340 mm
Q2. Design a rivet that is utilized in a double riveted butt joint which connects two 12 mm thick plates. The efficiency of riveting joint is 80% and the pitch is 80 mm. If the allowable stresses for the plate material are (tensile stress o 100 MPa, shear stress - 75 MPa, bearing stress oc= 180 MPa) and for the rivet material are (tensile stress o-120 MPa, shear stress T-90 MPa, bearing stress 6 = 200 MPa), use F.S. = 1.