The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 10500psi for the bronze segment AB and 14500psi for steel segment BC. Determine the diameter of each segment in inches so that each material is simultaneously stressed to its permissible limit when the torque T-16.6kip-ft is applied as shown. The shear moduli are 6E6psi for bronze and 12E6psi for steel. The diameter of Bronze. A Bronze 6.5 ft T Steel 4.5ft inches in 2 decimal places

The ends of the compound shaft are attached to rigid walls. The maximum shear stress is limited to 10500psi for the bronze segment AB and 14500psi for steel segment BC. Determine the diameter of each segment in inches so that each material is simultaneously stressed to its permissible limit when the torque T-16.6kip-ft is applied as shown. The shear moduli are 6E6psi for bronze and 12E6psi for steel. The diameter of Bronze. A Bronze 6.5 ft T Steel 4.5ft inches in 2 decimal places

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Explanation it correctly
Question 5 1 pts A pipe system has a discharge of 0.0316 m3/s with n = 0.013. Find the total loss of head between A and F. in m Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: 3 Pipe Length (m) Dia (mme) AB 180 150 BC 60 150 BE 150 150
The height of the fluid inside the tube after immersion is 1⁄8 the height of the cylinder glass tubing. It was immersed into a tank of a cleaning solvent with specific gravity of 0.83. The remaining length of tube above the surface is 6 cm. Determine the volume of the liquid inside the 4cm diameter tube in cubic cm . Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: cm3 Decimal Places required in the final answer: 3
5. Question number (5) WASTEWATER ENGINEERING Civil Engineering Clear handwriting please
12 2011KO Weeke Priv Tern Question 11 Consider the tank shown in the figure. The gate is rectangular in shape with width into the paper of 2.1 ft. Given: h = 4.0 ft B = 4.4 ft 0 = 31° Gasoline, sg=0.70 Ks- h Gasoline Ø Calculate the eccentricity (inches) of the hydrostatic force on the gate Express your answer in 2 decimal places. B hp
(Attach your solutions at the end of this file HIGHLIGHT YOUR FINALANSWER WITH COLOR YELLOW use two decimal places for your final answerswith correct units.)
I need a quick solution within 10 minutes With my best wishesTon.
I need a quick solution within 15 minutes With my best wishesTon.
190 Determine the magnitude of Q if the particle is in equilibrium given that 0 = 32.3° and P = 0011.png 7 F 24 A Round off ONLY on the FINAL ANSWER expressed in 3 decimal places. Add your answer
INTRUCTIONS: Read the problems carefully. Show your COMPLETE and NEAT solution. Box ALL intermediate and final answers, round them to the nearest thousandths (three decimal places). Do not forget to affix the corresponding units. Situation 1. Locate the Centroid from point O. Also, determine the moment of inertia about ë and x 10m 18m d = 4m 45° 5m 8m 12m ----
A pressure gauge at elevation 12m at the side of an open tank containing a liquid reads 80 kPa. Another gauge at elevation 7m reads 120 kPa. What is the elevation of the liquid surface? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: m Decimal Places required in the final answer: /Zero
Please provide a clear and complete solution. Answer quickly for I have 30 minutes left. Thank you.