The load impedance in the power transmission system shown absorbs 6 kW and generates 8 KVAR (i.e., capacitive). The sinusoidal voltage source develops 8 kW. (a) Find the magnitude of the line current I in the circuit. (b) If the load is represented by a series impedance R1 – jX1, find the values of Rį and X1. i 25 0 1000/0 V (rms) Source Line Load

The load impedance in the power transmission system shown absorbs 6 kW and generates 8 KVAR (i.e., capacitive). The sinusoidal voltage source develops 8 kW. (a) Find the magnitude of the line current I in the circuit. (b) If the load is represented by a series impedance R1 – jX1, find the values of Rį and X1. i 25 0 1000/0 V (rms) Source Line Load

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.14MCQ: The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load...

See similar textbooks

Similar questions

(a) Transform v(t)=75cos(377t15) to phasor form. Comment on whether =377 appears in your answer. (b) Transform V=5010 to instantaneous form. Assume that =377. (c) Add the two sinusoidal functions a(t) and b(t) of the same frequency given as follows: a(t)=A2cos(t+) and b(t)=B2cos(t+). Use phasor methods and obtain the resultant c(t). Does the resultant have the same frequency?
An industrial load consisting of a bank of induction motors consumes 50 kW at a power factor of 0.8 lagging from a 220-V,60-Hz, single-phase source. By placing a bank of capacitors in parallel with the load, the resultant power factor is to be raised to 0.95 lagging. Find the net capacitance of the capacitor bank in F that is required.
Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor, and a 4 capacitor. (a) Draw the circuit diagram. (b) Compute the series impedance. (C) Determine the current I delivered by the source. Is the current lagging or leading the source voltage? What is the power factor of this circuit?
The instantaneous power absorbed by the load in a single-phase ac circuit, for a general R LC load under sinusoidal-steady-state excitation. is (a) Nonzero constant (b) Zero (c) Containing double-frequency components
The active and reactive powers of an inductive circuit are 60W and 80VAR respectively. The power factor of the circuit is ___. a. 0.8 lagging b. 0.75 lagging c. 0.5 lagging d. 0.6 lagging
d. 565.685 V If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b.-12000 + j16000 VA O c. 12000 + j16000 VA O d. None of these Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im voltage source is FENG300 MINTERM
For the system in the figure: Find the total average power, total reactive power, total apparent power, and total power factor. Find the current Is (in phasor form). If the loads can be modeled as a resistance in series with a reactive element (capacitor or inductor), find the impedance of each load. Confirm the result of part B using the input voltage and the result of part C. ..
A 60 Hz sinusoidal voltage v = 141sinwt is applied to a series RL circuit. The values of the resistance and the inductance are 3 ohms and 0.016 henry respectively. a) Compute the rms value of the current and its phase angle with respect to the voltage.b) write the expression of the instantaneous current.
A 60 Hz sinusoidal voltage v = 141sinwt is applied to a series RL circuit. The values of the resistance and the inductance are 3 ohms and 0.016 henry respectively. a) Compute the rms value of the current and its phase angle with respect to the voltage. b) write the expression of the instantaneous current.
41. Two ac sources feed a common variable resistive load as shown in figure. Under the maximum power transfer condition, the power absorbed by the load resistance R, is lall 6 2 j8 2 6 2 11020 ( 0706 O9020° (a) 2200 W (b) 1250 W (c) 1000 W (d) 625 W
1- What is the mutual admittance, Y34, of the electric circuit shown in Figure ? Select one: a. 2+j3 b. 0 c. -2+j3 d. -2-j3 2- The admittance of the impedance -j0.5 is given by: Select one: a. 2j b. 4j c. -4j d. -2j Please help me as fast as possible please. PLEASE ANSWER ALL THE QUESTIONS COMPLETE STEP BY STEP PLEASE. THANKS.
ESSAY: Describe what happens to the power in this RLC series circuit as the capacitance decreases. Explain in general terms why the observed change should occur. Understand the effects of basic electrical components on the average power of the system and the concept of power factor. Differentiate between average power and real power.