n industrial load is fed from an AC voltage source (V.) via a transmission-line feeder with an mpedance Zline. The load operates at 30 kW, 0.8 pf lagging and voltage of 240 V-rms angle 0°. he real power and reactive power dissipated in the transmission-line feeder are 1.8 kW and 2.4 EVAR, respectively. ) Draw a schematic diagram of the circuit. 5) Find the impedance of the transmission-line feeder Zine. b) Find the magnitude and the phase angle of the voltage source.

n industrial load is fed from an AC voltage source (V.) via a transmission-line feeder with an mpedance Zline. The load operates at 30 kW, 0.8 pf lagging and voltage of 240 V-rms angle 0°. he real power and reactive power dissipated in the transmission-line feeder are 1.8 kW and 2.4 EVAR, respectively. ) Draw a schematic diagram of the circuit. 5) Find the impedance of the transmission-line feeder Zine. b) Find the magnitude and the phase angle of the voltage source.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

The rms value of v(t)=Vmaxcos(t+) is given by a. Vmax b. Vmax/2 c. 2Vmax d. 2Vmax
For the system in the figure: Find the total average power, total reactive power, total apparent power, and total power factor. Find the current Is (in phasor form). If the loads can be modeled as a resistance in series with a reactive element (capacitor or inductor), find the impedance of each load. Confirm the result of part B using the input voltage and the result of part C. ..
Draw the sinusoidal waveform of the AC voltage and current for the given loads below. Describe the characteristics of the waveform for each load. A. Pure resistor B. Pure inductor C. Pure capacitor
lši vl pir:10 Expert Q&A + 1. For the circuit in Figure: a. Determine I, VR, and Ve in phasor form. b. Calculate the total power factor, and indicate whether it is leading or lagging. c. Calculate the average power delivered to the circuit. d. Draw the impedance diagram. e. Find the voltages VR and Vcusing the voltage divider rule and compare them with the results of part(a) above. + Uc - + Ug - 30 2 L = 0.2 H L =0.2 H C = 4 µF e = V2(20) sin(377t + 40°) Expert Answer Home Search More II
A single-phase AC voltage controller has a resistive load R = 10 Ohm, and the RMS input voltage is Vs = 230 V, 60 Hz. The delay angle is 120 degree. Then power factor of the circuit is: Select one: O a. 1 O b. 0.75 O c. 0.44 O d. None of the above O e. 0.9
A single phase AC chopper supplies a pure inductive load of 0.02H from 220V, 50HZ AC supply. The triggering angle of the thyristors is 100°. (Assume the circuit is ideal.) a. Sketch the circuit b. Develop the load current expression and find the decay angle of the load current c. Sketch the load voltage and load current waveforms d. Calculate the RMS value of load voltage e. Calculate the RMS value of load current f. If the triggering angle of the thyristors is chosen as 60°. Explain the operation of the circuit.
Q2. A series of motor (Load 1) and lighting (load 2) are connected to an AC source as shown in Figure Q2. The AC source, Vs, supplies 415220° V with frequency 50 Hz. Based on this information: 5Ω 100mH : 15 2 Load 1 Load 2 i) Calculate the total load impedance. Vs ii) Calculate the current, I. Figure Q2. Write the waveform expressions in frequency domain for Vs and I. Draw a phasor diagram consists of Vs and / and state the relationship between Vs and I. (ii) (iv) Determine the power factor and calculate the real power, reactive power and apparent power. Establish the power triangle for the load.
For the circuit in the figure below, determine the load impedance that maximizes the average power drawn from the circuit in the figure below. What is the maximum average power?
A load is rated at 440V(rms), 7.5A(rms) and 3.3KW when connected to a 50HZ source. Find the load impedance.
A 230 V, 50 Hz a.c. supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in series with a 6.8 F capacitor. Calculate impedance and power consumption and power factor. Now ,In above a.c. circuit, A inductor of 0.2H is connected in parallel with the power supply, find new power factor and power consumption.
A DC-DC Chopper Circuit with an RL Load has an output current waveform shown below with a duty cycle of 50% and 1ms period. If it has a resistance of 1ohm and an inductance of 10mH, find the source voltage. 5A 2A ton toff output _current
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms