A sinusoidal voltage source of v(t) = 170 cos(2n60t) Volts is applied to a non-linear load, resulting in a nonsinusoidalcurrent with the expression i(t) = 10 cos(2n60t + 30°) + 5 cos(4n60t + 45°) + 2 cos(8r60t + 20°).• Determine:• The power absorbed by the load.• The power factor of the load.• The distortion factor of the load current.• The THD of the load current.• The total Apparent Power.

voltage is, v(t) = 170cos(2π60t) current is, i(t) =10cos(2π60t+300)+5cos(4π60t+450)+2cos(8π60t+200)…

• Asinusoidal voltage source of v(t) = 170 cos(2m60c) Volts is applied to a non-linear load, resulting in a nonsinusoidal current with the expression i(t) = 10 cos(2m60t + 30°) + 5 cos(4n60t + 45°) + 2 cos(8r60t + 20°). • Determine: • The power absorbed by the load. • The power factor of the load. • The distortion factor of the load current. • The THD of the load current. • The total Apparent Power.

• Asinusoidal voltage source of v(t) = 170 cos(2m60c) Volts is applied to a non-linear load, resulting in a nonsinusoidal current with the expression i(t) = 10 cos(2m60t + 30°) + 5 cos(4n60t + 45°) + 2 cos(8r60t + 20°). • Determine: • The power absorbed by the load. • The power factor of the load. • The distortion factor of the load current. • The THD of the load current. • The total Apparent Power.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A sinusoidal alternating voltage has an r.m.s. value of200 V and a frequency of 50 Hz. It crosses the zero axis in apositive direction when t = 0. Determine (i) the time when volt-age first reaches the instantaneous value of 200 V and (ii) thetime when voltage after passing through its maximum positivevalue reaches the value of 141.4 V.
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. a = 50° T1 50 2 ot Vs = 300 sin 100rt T2 ot
1. -) A sinusoidal voltage source in placed in series with a DC voltage source and produces an output of: v(t) = 70.7cos (377t) + 20 volts [ 70.7 = 50√2] Calculate: a. v²(t) b. Vrms C. The magnitude of the RMS current if the combined source is placed across a load of Z=4+j3 ohms (if you have trouble with part b, just assume a voltage of 100 Vrms for part c)
The instantaneous values of two alternating currents are given by i, = 20 sin wt and i, = 10 sin (wt + :) A. Find the sinusoidal expression for (i1 + i2) by drawing phasors and by calculations. Two alternating voltages are given by vị = 120 sin wt volts and vz = 200 sin(wt -) volts. Obtain the sinusoidal expression for v1 – v2 by resolution of phasors.
Across a 230V, 60Hz powers supply is a 15ohm non-inductive resistor. What is the equation of the resulting current? A. 21.68sin377t B. 26.55sin377t C. 15.33sin377t D. 28.16sin377t
Electrical load that draws current whose impedance varies throughout the cycle of the input ac voltage waveform is known as nonlinear load. True False
Q2. For the circuit shown below, sketch the current waveforms iş and io and determine the Average and RMS for both currents. a = 50° TI 50 2 Vs = 300 sin 100zt ( cot T2 in cot
1. Solve for I rms. 0.785 and b = 3.37. a = i(wt) = 21.8 sin (wt – 1.312) – 50 + 75.0e¯®t/3.77 A for 0.785
A sinusoidal current i1(t) has a phase angle of 30°. Furthermore, i1(t) attains its positive peak 2 ms earlier than current i2(t) does. Both currents have a frequency of 200 Hz. Determine the phase angle of i2(t).
Q1 Consider the mathematical expression of the voltage and current waveforms given below: v = -1 sin(ot + 20°) i = 10 sin (at - 70°) (i) Calculate the phase shift between the voltage v and the current i. (ii) Evaluate the phase relation between the voltage v and the current i. Q2 The sinusoidal current i = 4 sin(50000t – 40°) is plotted in Figure Q2. Determine the time 4,4 r (us) 40 Figure Q2
Problem #7) Specify whether each of the statements are TRUE or FALSE. D Reactive Power is a measure of the average power consumed by reactive (capacitive and inductive) loads. When connected to an AC voltage source, the instantaneous power (rate of energy transfer) supplied to a resistor varies at a frequency that is 2x the frequency of the applied source voltage. The magnitude of the impedance of a capacitor supplied by an AC source will increase as the source frequency increases. An AC source that has an RMS magnitude of 100V will supply the same average power to a resistor compared to a 100V DC source. The voltage across a capacitor is proportional to the rate of change of the current flowing through the capacitor. The magnitude of the impedance of a resistor supplied by an AC source does not vary as the source frequency increases. A complex impedance Z=R+jX, that has non-zero resistive and reactive components, will consume both real and reactive power when supplied by an AC source.…
The admittance of a network is (0.05– j0.08) S. Determine the values of resistance andreactance in the circuit if they are connected (a) in series, (b) in parallel.