The lap joint of a tension member is shown. The plate is 252 mm wide and 12 mm thick. The bolts are 20 mm in diameter and the holes are 3 mm larger than the bolt diameter. Use A36 steel. a. Determine the safe value of P based on tension net area. b. Determine the safe value of P based on tension bearing failure. c. Determine the safe value of P based on tension block shear

Q: 1. Determine the allowable load Pa based on bearing at bolt holes. (ASD) 2. Determine the ultimate…

A: Given:- Thickness of plate, t=16 mmDiameter of bolts, d=22 mmNumber of bolts, n=6S1=40 mmS2=80…

Q: 2.10 A square yellow it is subjected t the allowable t mum allowable cross section if

A:

Q: 60 b P P 150 100 100 100

A:

Q: hexagonnal head 60 mm threads bolt diameter @ threads 32 mm bolt diameter - 38 mm T=80 kN Calculate…

A: We have to determine the value of tensile stress in the body of the bolt and tensile stress at the…

Q: A steel angle is bolted to a gusset plate with three 20 mm diameter bolts, as shown in the figure.…

A:

Q: A PL ½ x 8 tension member is connected with six 1-inch diameter bolts as shown in the figure below.…

A: Answer We are given  Plate 1/2 x 8 bolt diameter  = 1 in A36 steel Shear lag factor U = 0.1

Q: III. Calculation questions (1) s) A 300 × 10 mm plate of A36 steel is used as a tension member. The…

A:

Q: The splicec connected 248 MPa сес CO

A:

Q: A flexural member is fabricated from two flanges plates 1" x 20" and a web plate 1/2" x 22". The…

A:

Q: The truss is loaded with service loads (Dead load and Wind Load) as shown in the figure. Members DE…

A: The truss is given as To find:- Force in member DE

Q: allowable

A: Block shear strength Agv =12in2×4 in= 4.00 in2Agv = 4.00 in2Ant = 12in10in = 5.0 in2Ubs = 1.0Rn…

Q: 1-66 Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be, if the…

A: Force = 22.3 kN or 22300 NDiameter of shank, d = 12 mm Thickness (t) = 8mm

Q: -P 38 63 63 38 252 63 63 63 63

A:

Q: 10 mm 20 mm The assembly above is comprised of a 10mm-diameter steel bolt, and a 20mm-diameter,…

A: option (d) or last option is correct  the explanation is given below

Q: 7 7a 7b 7c Alaterally supported beam was designed for flexure. The beam is safe for shear &…

A: Sx of 8"x8"x7.94mm is 371.99x103 mm3

Q: ISA 75 x 75 x 8 mm serves as tensile member. This angle is welded to a gusset plate as shown in…

A: Note : This question is related to Indian Standard Code as asked in the problem. Given data,  ISA…

Q: A bolted connection shown is bolted with a A-325 bolts with an allowable shearing stress of 207 MPa.…

A:

Q: A PL 38 x 6 tension member is welded to a gusset plate as shown in figure. The steel is A36. PL % ×…

A: Note:- Hi! Thank you for the question, As per the honor code, we are allowed to answer three…

Q: The following image shows a front and side view of the column connection. The bolts have a diameter…

A:

Q: Found solutions, steel structure

A:

Q: 4. An A992 WF steel section is used for the tension member shown in the figure. The bolts are 20mm…

A: Section W14x68bolt diameter, db = 20 mmA992 grade of steel:fy = 345 MPafu = 450 MPaTo find:a. The…

Q: The details of an end bearing stiffener are shown in Figure . The stiffener plates are 9⁄16-inch…

A: A572 Grade 50:Fy=50 ksi   Calculating the bearing strength: Apb=6-0.5×916×4=12.38 in2Rn=1.8 Fy Apb…

Q: 1-66 Figure P1-69 shows a bolt subjected to a tensile load. One failure mode would be, if the…

A:

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate Fy = 248 MPa Fu =…

A:

Q: 000 -P 38 63 63 38 252 63 63 63

A: A lap joint is the joint between two bits of metal wherein the edges or closures are covered and…

Q: 2. The figure shows a plate having a width of 400mm and thickness of 12mm is to be connected to…

A:

Q: 4. An A992 WF steel section is used for the tension member shown in the figure. The bolts are 20mm…

A: A W16x67 is given , we need to find out a. The nominal strength based on gross section yielding.b.…

Q: The angle shown in the figure is L 7 X4 X 7/16. Steel used is AS72 Gr. 55 steel. Diameter of bolts…

A: diameter of bolt = 1.125inch distance between two bolts=3inchs Ag=4,62in2 by steel table fy =70ksi…

Q: A bearing type connection is shown in Figure 3.19. The diameter of A 325 bolts is 22 mm and the A572…

A: Tensile capacity, the maximum load that a material can support without damage when being determined…

Q: Calculate the value of P so that the allowable tensile stress on net area will not be exceeded. USE…

A:

Q: Calculate the tightening torque for an SAE 5, ASTM449, 13UNC grade bolt with a diameter of 1/2 inch.…

A: The application of preload to a fastener by the turning of the fastener's nut. Friction points…

Q: The two plates are joined together using a rectangular pin. What is the smallest width of the plates…

A:

Q: A tension plate shown below is used to support suspended load "T". Gusset Plate- Fy = 248 MPa Fu =…

A: Given;

Q: Situation 8: For the connection shown in the figure. Pu = 80 KN, x1 = 200, x2 = 100, y1= 50, y2 = y3…

A:

Q: Shear strength value τ = 200 MPa The contents associated with bolts are given. P = 70 kN required…

A: Given, P =70 kNτ = 200 MPa

Q: A bracket shown in the figure 6.9 carries an eccentric load of 30 kN at an eccentricity of 200 mm.…

A:

Q: An A36 tension member shown in the figure is connected with three 19 mm diamter bolts. Diameter of…

A: