The two plates are joined together using a rectangular pin. What is the smallest width of the plates and pin if the load applied is 45 KN. The allowable tensile stress is 180MPA and the allowable shear and bearing stress are 120MPa and 380MP. respectively. rectangular pin 士 T0 mm P P

Q: own in millimeters. Note: DRAW OR ILLUSTRATE THE SUB-AREAS AND INDICATE THE CENTROID OF EACH…

A: To find the centroid-

Q: Prepare the details estimate for the following 2 roomed building

A: In this question, we have to calculate the total estimate of works

Q: Differentiate and discuss the common hardness testing methods

A: Hardness testing: - It is defined as a non-destructive test method which is used to determine…

Q: Please describe the quality control of concrete construction.

A: Any structure to be durable, high strength and also for a good view, much-needed factor is quality…

Q: 1. ONLY ATTACH PHOTOS NEEDED. a. ATTACH THE PHOTOS SHOWING HOVW THE SOUNDNESS OF CEMENT TEST IS DON…

A:

Q: Don't waste my question. No wrong answer. House storage 95 ft x 65 ft must be finished with the drop…

A:

Q: To be classified as a tile, a unit must have what percentage voids?

A: option B is correct

Q: Give 100 types of concrete failure

A: Carbonation and chloride contamination of the concrete are the two most typical reasons of failure.…

Q: What type of building systems are CLT panels used for?

A:

Q: 1=5 ft, locate the centroid (z,y) of the composite area. (Figure 1) re 1.5 ft 1 ft -3 ft- 1 of 1…

A:

Q: What are the similarities and difference between the actual ASTM C143 standard and the procedure…

A: In ASTM C143, the test method includes the determination of the hydraulic cement concrete slump in…

Q: 2 ft I ft 2 ft 1 ft 3 t

A:

Q: What are the plywood exposure durability classifications? Give an example of where each could be…

A: Plywood is manufactured in four durability classification namely exterior, exposure 1, exposure 2…

Q: Where exactly in these designs is there a lack of coherence, and what types of things might be done…

A: Coherence describes the properties of the interrelation between physical quantities of a single wave…

Q: Briefly describe Mix Columns

A: To describe Mix columns

Q: How to conduct a rebar tensile strength test?

A: Introduction : A sample is typically tugged to its breaking point in a simple tensile test to…

Q: What's the advantage of Composite structures?

A:

Q: how do you find SSD?  how is SSD 1.47?how do you determine breaking conditions? How is it 2.5?

A: The speed of the vehicle = 40 mph The gradient of the uphill = 5% To determine:- The value of the…

Q: GIVE 10 DISADVANTAGES OF USING HOLLOW BLCOKS

A: Disadvantages of using hollow blocks are : High Maintenance cost Load bearing capacity of the wall…

Q: How to Design Sealant Joint.

A: Sealants joints are the most underrated joints but they are the important joints when it comes to…

Q: Describe the auger method.

A: Auger method:

Q: What is the recommended minimum diameter (mm) for temperature bars in one way slab? Express your…

A:

Q: Assuming the following information • Parapet is 12550 mm long Blocking is 1x2 dimensional lumber…

A: Solution:- Given data:- Length of parapet = 12550 mm Blocking is 1 x 2 dimensional lumber   To…

Q: What is adhesive strength testing?

A: Adhesive strength test:

Q: Sealing Joint seals In the Exterior Walls and whats its uses.

A: Joint sealers area unit accustomed shut open joints to stay water associated air out (both exterior…

Q: Define Plain portland cement concrete .

A: Plain Portland cement is the most widespread form of cement used as an essential component in…

Q: fé = 4000psi, Grade 60, NWC Psteel = = = = Pb Please calculate As = ?

A: Answer  We are given b = 12 inch d = 18 inch h = 21 inch steel cover = 3 inch f'c = 4000 psi Grade…

Q: efine the term crevice which is one form of corrosion.

A: Crevice corrosion refers to the attack of metal surfaces by a stagnant solution in crevices, for…

Q: Why are tapes sometimes used with sealants in joints?

A: For complete installation of sealants ,backup materials are required . Sealant's  depth is…

Q: What is the punching shear failure?

A: Punching shear failure: Punching shear is also called as two way shear. It is the shear that is…

Q: Define the following i) SMRF Structures ii) IMRF Structures

A: 1. The SMRF structures and IMRF structures are types of moment-resisting frames use to resist the…

Q: m REQUIREMENT: PCS- "THICK INTERIOR PLYWOOD WALLS PCS- ¼" THICK EXTERIOR HARDIFLEX WALLS PCS-…

A:

Q: (4) 3" L 14" 3" 4" 4#9 21" fo=3 ksi Nwc Grade 60 &Mn = ? steel

A:

Q: Please provide the enough information and definition of these construction terms:  Reinforced…

A: As per our guideline we are supposed to give  only first three answer of this question because this…

Q: List the points that are pertinent in the care of tapes.

A: In surveying most of the measurements is done with the help of tape, following are some pertinent in…

Q: Describe Applying the shotcrete wall surface.

A:

Q: he accuracy of the spread plate metho

A: The spread plate method is generally the technique to plate the sample of liquid that contains…

Q: What is the types of shrenkage ?

A: Shrinkage is characterized as the contracting of a solidified solid combination because of the…

Q: Il: DRAW THE SECTION DETAILS FOR RAIL AND SLEEPERS SECTIONAL DETAILS FLEXIBLE PAVEMENTS SEOTIONAL…

A:

Q: Provide clear and step by step solution Using LRFD, PL400x350 mm base plate, W12x120 column,…

A:

Q: Define Structural strength limit states

A: Limit state based approach;  This method is developed for designing a member based on a non-linear,…

Q: Search and draw other types of CONCRETE BLOCK (at least 8 types). -name of concrete block -usage -…

A: Name of the concrete blocks Usage  Size image  1. Solid Concrete Block  Used in load bearing walls…

Q: Q3/ List four points of the Engineering Properties for the Bricks?

A: Brick is one of the oldest materials used in engineering construction work. It mainly used in…

Q: Problem 1: Calculate Mn and check the minimum steel limit f'c =4 ksi, fy = 60 ksi. 2.5" 25" 6-#9…

A: Given doubly reinforced beam with values,Width of the beam, b= 12''Effective depth,…

Q: Number of modular bricks required for one cubic metre of brick masonary are

A: Brief concept introduction- Bricks- These are one the most common building materials used in the…