The impedance per phase of balanced Y-conected 3-phase load is Z = 66/12° Ohm, and it is connected to 3 phase positive sequence power grid which has the voltage of 369 V. Calculate the phasor magnitude of the line current of phase A in Amperes. The voltage of phase A will be taken as reference. Note: Write only the number, do not write the unit. Also extend your answer two digits after the comma.

The impedance per phase of balanced Y-conected 3-phase load is Z = 66/12° Ohm, and it is connected to 3 phase positive sequence power grid which has the voltage of 369 V. Calculate the phasor magnitude of the line current of phase A in Amperes. The voltage of phase A will be taken as reference. Note: Write only the number, do not write the unit. Also extend your answer two digits after the comma.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Number 17
A conventional phase transformer given in the figure will be connected as an autotransformer in two different ways. Each For a connection, find the input and output powers by drawing the connection. a) Connection of 1220 / 220V autotransformer b) 1000 / 1220V autotransformer connection
Referring to the circuit shown in Figure 1 below, solve the following problems: - i) Calculate the total impedance, ZT. ii) Determine the total current, Ir supplied by the generator iii) Determine the value of current at load impedance, I1, I2 and I3. iv) Calculate total real power, PT and reactive power, Qr supplied by the generator. v) Draw a power triangle of this circuit vi) Calculate the power factor of this circuit.
A load impedance, Zo = 10 + j 3 ohm, is connected to a source with line resistance equal to 3 ohm, as shown in the figure. Determine the apparent power supplied by the generator. The apparent power supplied by the generator is _____ VA.
For the system as shown in the following figure, convert the components to same base voltage and apparent power, by choosing 100 kVA as the base kVA and 2000 V as the base voltage for the generators. Redraw the single line diagram with the new per unit values. 15 KVA 2000 V Z=j0.3 pu 25 KVA 2000 V Z=j0.15 pu G1 G2 35 KVA 2000/8000 V Z=j0.2 pu Z=30+j100 Z=60+j120 pu O pu leee 35 KVA 8000/2000 V Z=j0.3 pu 35 kVA 2000/8000 V Z=j0.25 pu G3 10 KVA 2000V Z=j0.35 pu M 30 KVA 2000 V
In a +ve sequence 3-phase supply, _________________________ a. Angle between voltages in Y and R phase is 0 degree b. Angle between voltages in Y and R phase is 180 degree c. Angle between voltages in Y and R phase is 120 degree d. Angle between voltages in Y and R phase is 90 degree
Overhead lines.
Consider a 3-phase, 35 kV transformers with N1:N2 = 150:900. Calculate the secondary line voltage on no load if the windings are connected in i) Delta-Star [ ii) Star-Delta
Q1. For the system shown in Figure Q1, draw an impedance diagram in per unit, by choosing 100 kVA to be the base kVA and 2400 V as the base voltage for the generators. 10 KVA 2400 V G₁ Z=j0.2pu 20 KVA 2400 V Z=j0.2pu G₂ T₁ Transmission Line Z= (50+j200) 40 KVA 2400/9600 V Z=j0.1pu Fig Q1 T₂ 80 KVA 10/5 kV Z=j0.1pu M 25 KVA 4 kV
What is the max load demand of the following feeders 4152 MW, 2.891 MW, 815.20 KW, 905.12 KWand 1.972 MW A) 10,735.32 KW B) 12,815.32 KW C) 10,571 MW D) 12.052 MW